Models > 4KG25G7XSL4 > Instructions

4KG25G7XSL4 KitchenAid Mixer - Instructions

All installation instructions for 4KG25G7XSL4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KG25G7XSL4
31-45 of 110
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replace a broken attachment for an ancient KitchenAid

  • Customer: Kate from Vredenburgh AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 8 people found this instruction helpful
I decided to repair my grandfather's first generation, ancient KitchenAid mixer. The wire whip had come undone so that it couldn't be used.

Everyone was skeptical that I could find the part for such an old mixer, but I got the serial number and googled "kitchenaid + the part number + whip whip + repair." That search brought up PartSelect.com.

It was very easy to plug in all the info and find the part on PartSelect.com and 24.99 later, the part arrived on my doorstep.

I took it out of the box, fitted it to the attachment on the mixer and turned the mixer on. Viola! Worked perfectly!

Thanks PartSelect! Everyone is amazed that I found the part for such an old appliance.

mixer was very noisy when running and made a horrible grinding sound

  • Customer: Thomas from Bluffton IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.

teeth missing on worm gear

  • Customer: Ronald from Anna OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
removed cover annd snap ring removed gear and replaced with new,

Gear Stripped was trying to replace

  • Customer: Stuart from Pittsford NY
  • Difficulty: Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Could not get it properly installed. Had to take to a repair center for completion.

Plastic boke on the old thumb screw

  • Customer: Alice from St Louis MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

gear teeth worn off worm gear

  • Customer: Jamie from Jamestown ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
replace worm gear

Worm gear stripped.

  • Customer: Jerry from Southport NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
Remove covers, open gear box, remove lock ring and gears to deterime which gears were bad. Remove old grease, install new gears and pack with new grease.

Needed repair

  • Customer: Linda from Ivanhoe VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.

none

  • Customer: Joseph from Mentone CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.

Household (stand) mixer making weird noise

  • Customer: Linda from Anchorage AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

thank you,

  • Customer: Eleanor from Perry NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
my hasband did the work and i an so happy it is working good for me now,

plastic outer casing on tightening screw had broken

  • Customer: Peggy from Escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

motor would surge after a few moments of running then die.

  • Customer: Fred from Coeur d'alene ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 1 of 3 people found this instruction helpful
so easy to remove the switch. I first marked the wires, 1-2-3-4 and then removed them from the old switch. removed the old switch and replaced with the new one and plugged in the wires as per markings. tried it out before replacing the top and it works perfectly. no longer timid about effecting repairs on my own. the diagrams on the website were a great help. this is a great company to do business with. part was here in 3 days.

Gears had stripped due to housing crack and movement

  • Customer: Judith from Turtle Lake WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Took top apart and installed new housing and two gears. Reassembled

thumb screw broke

  • Customer: Ethel from Crystal River FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
it just screw in.
All Instructions for the 4KG25G7XSL4
31-45 of 110