Models > 4KG25G0XMC4 > Instructions

4KG25G0XMC4 KitchenAid Mixer - Instructions

All installation instructions for 4KG25G0XMC4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KG25G0XMC4
76-90 of 103
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

wire whip to kitchen aid was broken

  • Customer: patricia from Sidney IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
It was easy! I put in the model number for my kitchen aid and it showed a pitcher of it with a different model number but i trusted it and had it shipped to me. It came the next day!! I was so impressed by this. I would definitely order thorough. this company again!!

Clanking noise, motor strain/ ultimate burn out.

  • Customer: Francis from Plymouth MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First of all, go to the web site and download the schematics of the model #. It will show all the parts and part #s. Secondly watch a u tube video of the actual strip down process of the professional 600 series stand mixer. With this knowledge, do one of two processes 1: strip down the machine, remove the gears and check for defects- order parts. Or 2: replace all the parts( little money) and have a totally refurbished , smooth running mixer. I kept the good used gears for spares. I replaced 90 % of the internals ( including motor) and have a smooth running machine. I initially burned out the mother 2 months after initial purchase, sent it back under warentee, and received it back . Wen I stripped it down 10 years later, there was very little grease in the gear housing. This is what probable ruined the gears. Use plenty of grease in the housing and gears. The grease is one of the most expensive items, but you can't find it anywhere, so order it, along with everything else, from Parts Select.

Worm Gear teeth was stripped

  • Customer: Ronny from Clearwater KS
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top cover, remove snap-ring on shaft, slide top gear and worm gear off. Clean all the grease out and clean parts. Installed new worm gear and parts. Repacked with new grease, careful not to much, leaving room for expansion.

main shaft for beatter slipped way down

  • Customer: John from Kaukauna WI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced planetary assembly. Was not difficult to do.

Pin-bowl lost

  • Customer: Tina from La Farge WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply placed it in the slot and pounded until firmly in with a soft mallet. Thanks to your site I was able to find the piece easily and very inexpensively. Thank you so much. I would die if I couldn't fix this machine.

Broken Part to KitchenAid Mixer

  • Customer: PJ from Rome GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Great experience. Reasonable cost. Quick delivery. Would certainly use PartSelect again

The mixer sounded like the gearbox was full of gravel.

  • Customer: Herbert from Glendale AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The transmission housing was cracked and one of the bearings was broken. I replaced both of them, but the mixer really didn't sound any better. So I replaced the gears in the transmission, and while that was better it still wasn't correct. I am going to replace the other bearing and the planetary shaft and see it that aligns everything a bit better. I believe the problem is the way the gear on the end of the motor shaft is working with the worm gear, the bearings are not keeping the correct spacing. Hopefully, the new one in the rear will fix the problem.

Part broken

  • Customer: William from North Olmsted OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Easy thanks to your instructions

didn't turn

  • Customer: robert from wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ordered the part and put in in with the help from the instant repairman

$500 mixer had only 1 yr. warranty

  • Customer: wilfred from north yarmouth ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
___ Remove silver decorative band/1 screw ___ Remove top of mixer/4 screws ___ Remove circuit board/2 screws ___ remove 5 wires from ckt. bd. (be sure where they go) ___ Install new ckt. bd. with proper electircal connections ___ test mixer/OK ___ Reassemble & retest/OK

Mixer stopped working and gave grinding sounds

  • Customer: brian from carlsbad CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Following Replacement Part Youtube instructions, I disassembled the mixer and found what caused the sounds and prevented the mixer from operating. The worm follower gear had been ground down by the worm gear. I found that the shaft from the planetary gear had not been adequately greased and siezed preventing the worm follower gear from turning. The worm gear is obviously made of harder material and thus, was able to wear away the follower. I appreciate the your help which saved having to replace a perfectly good/expensive mixer. Thanks.

Stripped worm follower gear.

  • Customer: Johnna from Childress TX
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watched the video. Ordered the parts. Watched the video again. Replaced the worm follower gear and bearings on the worm gear. Added grease. Installed new gear housing. Put it all back together and tested. Works like new. Now I get cakes and goodies again and have a happy wife who thinks I'm super handyman. Thanks

gears stripped

  • Customer: carole from new braunfels TX
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
watched the youtube video on how to repair a Kitchenaid Pro 600.

I broke my old Kitchen Aid's wire basket mixer part

  • Customer: Carole from North Granby CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I tried to use the broken mixer paddle for almost a year before I checked out the part broken on line. I easily found the part, and it arrived within a week--and fit perfectly! Thank you for making it so easy to do on line!

speed controll switch. would start and stop on its own.

  • Customer: brian from saint simons island GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
replaced Speed control board. less than 40.00 took ten minuets from the time I started until we were making cookies.
All Instructions for the 4KG25G0XMC4
76-90 of 103