Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4KB25G1XTG3 > Instructions

4KB25G1XTG3 KitchenAid Mixer - Instructions

All installation instructions for 4KB25G1XTG3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KB25G1XTG3
16-30 of 103
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Nut Screw Plastic Housing Split that stabilizes attachments on top side of machine

  • Customer: Richard from Bayfield, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 7 of 7 people found this instruction helpful
I removed the old screw with a hand tool to avoid injuring my hand. I then used my hand to install the new screw. Piece of cake. Ordering from Part Select was was a breeze. The only minor issue was the part cost $4.33 and shipping was $7.25.

speed surged after mixer warmed up

  • Customer: Thomas from Christiana, TN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 8 people found this instruction helpful
Took off cover, marked leads, unscrewed two screws and replaced circuit board (speed swith unit). This one was really easy.

Stripped gear teeth

  • Customer: Roger H. from Polo, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 6 people found this instruction helpful
Removed rear band screw and band
remove 4 screws from head assembly and remove mixer head
remove 2 screws fastening speed control switch
remove 4 screws from gear box cover
remove cover and slide out bevel gear and replace
remove retainer ring and slide gear off shaft.
reassemble in reverse order, apply grease to gear teeth.
first time 25 minutes to inspect and reassemble
2nd time 5 minutes to teardown,replace parts, and reassemble
All manufactured assemblies should be this nice to work on.

Speed control failed to work properly

  • Customer: Christine from Maple Valley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 7 people found this instruction helpful
Unscrewed stainless steel Kitchenaid band, removed screws holding down the main housing to get to the speed control panel. Removed two screws from to release the speed control panel, replaced the panel with new part, and replaced all the screws to the main housing, and stainless steel band and it worked like new. So easy, and it only took about 15 minutes to repair.

worn gears had to be replaced (second time)

  • Customer: Vincent J. from Hudson, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 8 people found this instruction helpful
the hardest part is removing the retaining ring (didn't buy pliers)after that it is very easy, remove ring, top gear, center pin, bottom gear,worm gear(was removed first)the grease is pretty nasty,clean off the old grease and put it all back the way it came apart,with new grease.And then PRAY !!!!!!! THANK YOU PARTS SELECT for your wonder smart staff.

bevel gear, bearings and housing replacement

  • Customer: Thomas from Upperco, MD
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 12 people found this instruction helpful
The parts I received from PartSelect were higher quality than the original parts. The bevel gear and housing were originally plastic. The new ones are solid metal. The machine sounds and runs better than it ever did. The drawings from the website made this really easy. This will be my first choise for parts from now on.

gears were stripped from overload of bread dough

  • Customer: karl from Eureka, MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 5 of 6 people found this instruction helpful
At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.

The mixer would not raise the bowl

  • Customer: Stephen from Charlotte, NC
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 6 of 10 people found this instruction helpful
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spring back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.

teeth missing on worm gear

  • Customer: Ronald from Anna, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
removed cover annd snap ring removed gear and replaced with new,

speed control went. The beater would fly in any setting

  • Customer: Brandy from Thorp, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 6 people found this instruction helpful
I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.

all four feet on mixer damaged

  • Customer: ROBERT from ENDWELL, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looked good.

broken cog on gear

  • Customer: Linda from Greenfield, IN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
Researched the internet for a diagram of the mixer and used that to take it apart, clean everything, then install the new gear and new grease. Works great so far.

Gears were stripped and mixer would not mix

  • Customer: Gregory from Califon, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
This was easy once Igot all the parts. The mxer wouldn't mix and when I opened it up the drive gear between the motor and the planetary drive was missing some teeth. Turns out the bearing, which was sintered bronze, had broken so I needed a new gear, new bearing, and the jumping gear had broken the housing so I needed a new housing. The new gearing ( really a bushing since there are no rollers or balls in the "bearing") waws now steel and the molded plastic housing is now cast metal. Some new grease ( I had to buy a quart can of grease to get two tablespooons) a new gasket and put the screws in and we're back in business. Total repair time 10 minutes, total time to get all the parts 3 weeks,

Plastic boke on the old thumb screw

  • Customer: Alice from St Louis, MO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 2 people found this instruction helpful
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

mixer was very noisy when running and made a horrible grinding sound

  • Customer: Thomas from Bluffton, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 5 people found this instruction helpful
My husband removed screws and took top off mixer. Then he took out the gears and cleaned them from all the grease. After he did that he could see the gears that were all worn. We went on line ordered the new gears and in a couple of days the parts were here and he put them back in and greased it all again and put the top and screws back in place. Mixer sounds much quieter. Thank you.
All Instructions for the 4KB25G1XTG3
16-30 of 103