Models > 4KB25G1XOB3 > Instructions

4KB25G1XOB3 KitchenAid Mixer - Instructions

All installation instructions for 4KB25G1XOB3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KB25G1XOB3
91-96 of 96
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Speed control stuck from sugar/flour build up on slide

  • Customer: David from Dekalb IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Took housing off, removed computer board and disconnected speed control assembly from board. Soaked plastic slide in hot water and freed up mech. Discovered a crack in plastic slide from forcing it. Ordered new assembly and installed. TIP: Keep slide clean of substances that will jam it by cleaning occasionally with water. For a complete cleaning you will have to remove it. Total of 6 easy to reach screws.

Worn gears

  • Customer: Ronald from Spring Field VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took mixer apart and then the gear compartment. inspected components. Replaced the worn gears and re-greased the new parts. Put the gear compartment back together, tested the operation of the unit and then replaced the rest of mixer, re-tested and declared victory.

worn gear causing slippage under load

  • Customer: Rodney from Thornton NH
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed cover. Removed cover over gears. Used lock washer pliers to remove lock washer. Took out gears. Cleaned metal shavings from old gear and grease. Reassembled using new gear. Took about 15 minutes and saved $$ over sending mixer out for the repair.

Stripped worm gear

  • Customer: Johna from Ketchikan AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Looked at the schematic for this model on Parts Select. Removed Aluminum band screw, removed the 4 screws that hold the top of the mixer. Lifted the top off. Removed 4 screws and lifted the gear case. Removed snap ring and took off tapered gear. Removed pin and removed worm gear. Picked out the metal, in the grease, from the old worm gear, using a magnet then inserted new worm gear and put it back together in reverse order. There was plenty of grease and didn't need to add any.

Mixer wouldn't slow down

  • Customer: Sal from STATEN ISLAND NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the mixer, then I removed the Phillips screw holding the beauty ring, then removed the 4 screws that hold the motor housing together. I removed the housing top, and unscrewed the speed control switch. I marked each one of the connectors of the switch (there are 4) 1-4 then disconnected the speed sensor from the switch and the motor. Replaced the new sensor and connected that to the new speed control switch. reconnected the connectors to the terminals I took them from ( 1 - 4 ) screwed it into place. replaced the top motor housing, I screwed that back with the four screws. replaced the beauty ring and screw. plugged it in and tested it and it was like new

Broken Bevel Gear

  • Customer: robert from cypress CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
You must have new bevel gear and can of food grade grease, ordered together. 1. Remove screw from back of mixer, holding the trim band; remove band. 2. Remove four screws holding the top cover. 3. Remover cover 4. Remove two screws holding the PC board and motor speed control; lift board out of the way. 5. Remove four screws holding gear cover; remove cover. 6. Remove as much gear grease as is accessible; discard. 7. Remove snap ring from vertical shaft holding bevel gear. 8. Remove horizontal shaft/gear by lifting straight up. 9. Remove bevel gear by sliding up shaft. 10. Remove cross pin holding lower gear. 11. Remove lower gear by sliding up shaft. 12. Remove vertical shaft and rotating head by tapping on top of shaft. 13. Clean all grease from gear case and on all gears (ground metal from bevel gear will be in this grease). 14. Clean all grease from inside gear cover. 15. Making certain gear case is now clean of all old grease, use putty knife to place grease in bottom of gear case. 16. Rub light coat of grease on vertical shaft and slide shaft back up into bottom housing. 17. Slide lower bearing back down vertical shaft. 18. Reinstall cross pin holding lower gear. 19. Place grease on lower gear. 20. Slide bevel gear down vertical shaft, making certain recess in underside of bevel gear lines up and sits completely over top of lower gear; when the bevel gear is fuly seated the snap ring groove will just be showing on the vertical shaft. 21. Reinstall snap ring. 22. Lightly grease shaft of both ends og horizontal shaft/gear; make certain ball bearing on front of shaft is also greased. 23. Slide ball bearing, spacer and bronze bushing on front of horizontal shaft. 24. Silde bronze bushing on opposite end of horizontal shaft (flange on bronze bushing is placed facing the gear). 25. Place assembled horizontal shaft/gear into lower gear housing. 26. Liberally grease all gears, 27. Replace gear cover, replace screws. 28. Replace PC board and motor speed control. 29. Plug mixer in and run on lowest speed for at least 10 minutes;increase speed until satisfied gears ar running smoothly. 30. replace top cover and trim band. BAKE SOMETHING
All Instructions for the 4KB25G1XOB3
91-96 of 96