Models > 4KB25G1XOB3 > Instructions

4KB25G1XOB3 KitchenAid Mixer - Instructions

All installation instructions for 4KB25G1XOB3 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the mixer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4KB25G1XOB3
31-45 of 102
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The mixer only ran on high speed

  • Customer: Kenneth from Clovs CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
I replaced the speed control board, however that did not correct the problem. I received the part very quickly and the install was easy but obviously it did not correct the problem so I will be returning the part. Hopefully that will go well also.

gear teeth worn off worm gear

  • Customer: Jamie from Jamestown ND
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
replace worm gear

gears were stripped from overload of bread dough

  • Customer: karl from Eureka MT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 3 people found this instruction helpful
At the back of mixer is 1 screw that holds metal band. Remove to reveal 4 screws that hold top half of mixer. Inside locate transmission housing remove 4 more screws. Inside housing carefully scrape away grease and broken bits of gear. Take out worm gear drive shaft wipe off and inspect. Clean up grease inside tranny locate keeper ring on vertical shaft spread and slide off use 2 screwdrivers to jimmy gears up. Replace with new parts put back together and use fresh grease. Not too hard at all and alot cheaper than a new kitchen-aid.

Plastic boke on the old thumb screw

  • Customer: Alice from St Louis MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 1 people found this instruction helpful
unscrewed the old one........screwed in the new one, no chance for electrocution or power tools..........darn!

speed control went. The beater would fly in any setting

  • Customer: Brandy from Thorp WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I carefully removed the cover of my mixer. I first made sure that all of my part numbers corresponded, then I labeled the 5 wires that needed to be disconnected. I then disconnected the wires, removed the two screws holding the part in place, switched out the old for new, reconnected all of my wires. Mades sure everything looked tight, and put my cover back on. Works like a charm. I cried because what I really thought was going to be a $200+ fix, ended up costing me less than $50! And it was so easy.

Household (stand) mixer making weird noise

  • Customer: Linda from Anchorage AK
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!

plastic outer casing on tightening screw had broken

  • Customer: Peggy from Escondido CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
This is the tightening screw that holds the attachments into the motor unit of the mixer. Found your web site and reordered 2 replacement pieces (in case one breaks!). Very EZ and user friendly. Thank you!

thank you,

  • Customer: Eleanor from Perry NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
my hasband did the work and i an so happy it is working good for me now,

Mixer Feet startarted to disintergrate and leave marks on counter

  • Customer: Vernon from Orange Park FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 1 people found this instruction helpful
Called original Kitchen Aid and advised had been sold and to look for Kitched Aid on web. Found site, went to appliance diagram and obtained part number and ordered. When parts came in just unscrewed and replaced new feet.

Replacement of digital window in oven unit

  • Customer: Bedalia from Rialto CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
I did not do the repair myself, however, I contacted a suggested service company which in turn was a company I had used before when I had problems with my JenAir microwave. Excellent service, prompt and very professional. Thank you JenAir for your assistance in providing promptly the parts needed to complete this job.

none

  • Customer: Joseph from Mentone CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
followed directions given, removed all the old grease .did a short test run , then replaced with new grease. the reason the gear was striped was my fault mixing too much bread at one time. we have a coffee house and use the mixer every day.

Gears ground when roller attachment applied.

  • Customer: Michael from Tomahawk WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael

attachment driver will not work

  • Customer: jose from denver CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.

Gears had stripped due to housing crack and movement

  • Customer: Judith from Turtle Lake WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 1 people found this instruction helpful
Took top apart and installed new housing and two gears. Reassembled

thumb screw broke

  • Customer: Ethel from Crystal River FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
it just screw in.
All Instructions for the 4KB25G1XOB3
31-45 of 102