Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4FIKIT99

4FIKIT99 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for 4FIKIT99

If you know the ice maker repair part you need, you can browse the list of all parts on the 4FIKIT99, or you can search by name or part description. You can also find your part by where it is located on the 4FIKIT99 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for 4FIKIT99 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the 4FIKIT99

[Viewing 1 of 1]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.40

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

Order within the next 1 hr and 38 mins and your part ships today!
$5.00

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

Order within the next 1 hr and 38 mins and your part ships today!
$30.02

BRACKET

Order within the next 1 hr and 38 mins and your part ships today!
$11.33

SCREW

Order within the next 1 hr and 38 mins and your part ships today!
$4.94

SCREW

Order within the next 1 hr and 38 mins and your part ships today!
$7.98

Icemaker Fill Tube Extension Kit

Order within the next 1 hr and 38 mins and your part ships today!

Valve Nut

This nut is used for water inlet valves.

$131.90

MOTOR-MODL

Order within the next 1 hr and 38 mins and your part ships today!

PARTS-MISC

CLAMP

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 100 of 109 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 90 of 106 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more

No ice in ice trey

  • Customer: Wayne from Leesburg, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 80 people found this instruction helpful
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and star... read more