Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 4CA2762XWW0

4CA2762XWW0 Whirlpool Washer - Overview

Get Parts and Repair Help for 4CA2762XWW0

If you know the washer repair part you need, you can browse the list of all parts on the 4CA2762XWW0, or you can search by name or part description. You can also find your part by where it is located on the 4CA2762XWW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 4CA2762XWW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$11.77

Direct Drive Motor Coupling

The direct drive motor coupling, also known as a coupling kit, is a newer version of the part and is used in your washer. The piece includes new metal sleeves that have been added ...

$28.33

Direct Drive Water Pump

This direct drive water pump, also known as washing machine drain pump or washer drain pump, is manufactured for washing machines that do not have belts. This is a genuine Whirlpool part with two ports for water to pass through, a large one and a smaller one, that will need replacing if the washer has a defective pump. Tools needed are slip joint pliers, a flat blade screw driver, and a putty knife. Sandpaper might also be needed to remove rust from internal parts to install the new pump. The washer will have to be disconnected from power and tilted on its back.

$45.80

Clutch Assembly

A clutch assembly is found in your washing machine and is responsible for spinning the basket during the spin cycle. A worn-down clutch can lead to a slower spin which can lead to ...

$2.92

Suspension Spring

The suspension is meant to support the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down, or perhaps has stretched out and lost its spring, it could cause the load to be off-balance which can cause excessive shaking, moving, noise and possibly leaks. For this repair, you will need a 1/4 nut driver, a putty knife, a flat blade screw driver, and a pair of needle nose pliers. Disconnect the power supply, fill hoses, and drain hose to give you safe and easy access (have a container nearby for water left in drain hose). This item is sold individually.

$3.56

Tub Spring

This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of th...

$4.63

Screw & Washer (5/16-24 x 1)

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$12.21

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$6.88

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$4.36

GASKET

This part may also be referred to as a main outer tub seal. This part prevents leaking from the bottom of the tub. The gasket is approximately 2 inches in diameter to the outer edg...

$16.48

Suspension Pads - Package of 3

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 888 of 942 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

Water pump leaking when machine used.

  • Customer: Tom from Granby, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 530 of 559 people found this instruction helpful
The hardest part of this job was pulling the machine away from the wall so the hoses could be disconnected and the machine flipped onto it's back. Putting the machine on it's back does two things. It drains the water left in the bottom of the tub so it won't pour out onto the motor when the old pump is removed, and gives the necessary access to the pump. ... read more

spin cycle did not engage

  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 369 of 393 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more