49-2848-23-03 Tappan Dryer - Instructions

Determined that the coil on the gas valve wasn't pulling in to ignite. Using an ohmmeter, I determined the coil was open. The coil was removed by pulling off the wire connecter and removing the two phillips screws holding the bracket over the two coils. The coil then slides out. I slid the new coil into place, replaced the bracket and two screws and reconnected the wire connector. It worked immediately. The actual repair only took 15 minutes. The bulk of the time was spent tracking down which part had failed.

Removed 4 screws from 8" service panel from rear of dryer removed panel
Removed 4 screws holding rear of dryer top, removed rear brackets. compressed spring retainers on front of dryer top, removed dryer top.
Removed 2 screws from inside of dryer front, removed dryer front.
Removed old belt, cleaned machine, installed new belt on dryer drum, inspected rear service panel to insure belt had reached the drive motor.
Reinstalled front of dryer, being sure to hold drum up in position to match front panel..
Went back to rear service panel and installed belt on motor pulley and tension pulley.
Set top back on dryer, test ran dryer for short time to ensure all was functioning properly.
Installed dryer top, and brackets.
Installed service panel.

1. After checking the Parts Select website for some useful information I unplugged the dryer.
2. I popped the two clips holding the top down and lifted the top up and out of the way.
3. I used the 8mm socket and screwdiver combo to remove the two screws holding the front of the dryer on. These screws are so close to the sides of the dryer that you need something very thin to seat the socket, it is so thin a small rachet would not fit.
4. Once the to screws are free to forget to unhook the two wires that lead to the automatic cutoff switch on the right. Label them and move them out of the way.
5. The front of the dryer should pivot forward and come right off. Don't forget about the two clips at the bottom, they are not really attached to anything and can be easy to lose.
6. Get your screwdriver and dive into the drum, on the back should be three screws, take those out.
7. Spin the dryer around and take off the vent cover in the lower left corner of the back of the dryer, watch out the socket is a smaller size.
8. Once inside there is an idler pulley like on the back of a ten speed bike, pull the tension out of it and take the drive belt off the pulleys.
9. The drum should be able to be pulled out the front of the dryer, set aside with the door. The screws on my dryer were so tight I had to use a hammer drill to remove them.
10. This is were I got stuck, no one mentioned how to get the bearing plate off, as if everyone would just know. You must lift up on the bearing plate and once it moves up then you can pull it out.
11. Use the 8mm socket to unscrew the old plastic bearing guide. The small metal clip on the back of the dryer will fall off with the grounding ball bearing.
12. With brum bearing kit in hand start off by putting as much high temp lubricant as you can into the bottom of the new bearing guide. I also use a little lubricant like glue to hold the new grounding ball bearing in the little hole on the back of the bearing guide.
13. Here is the tricky part you have to screw the bearing guide into the the dryer while simulaneously holding the little metal clip in place on the back of the dryer. I used duct tape to hold the metal clip and once the screws got started I just took the tape off.
14. Now you have to do the impossible, the bearing must be screwed to the drum. So unless you have 7 foot long arms you can't hold the bearing and drive the screws. Another problem is the bearing itself, the holes are not the same size as the original and they are not threaded. I stripped every screw that came with the kit trying to get them through the metal of the bearing.
15. With an unwilling victim holding the bearing steady I finally got a replacement screw to seat through the bearing. Once you get one the rest are easier.
16. You are ready to reassemble, after vacuuming everything ou, pick up the drum making sure the belt is around the drum about where it was when you took it off. Push the drum through the front of the dryer all the way to the back, aim a little high so the bearing can move down and seat in the bearing guide.
17. Tuck the clips on the front panel of the dryer into the bottom front edge of the dryer and the whole front should pivot up, when you get it almost closed you will have to lift the drum and set it on the front bearing in the door.
18. While holding the front of the dryer on you have to reach inside and get the 8mm screw started on the left or right, if you let go the front of the dryer will pop off and you have to start over with the pivot. Now is a good time to have a magnet on a stick so when you drop the screw or screw driver you don't have to take the front off to retrieve your tools.
19. Once the front is on reconnect the two wires to the switch in the front of the dryer. Remember the ones you were supposed to have labeled earlier.
20. Close the top of the dryer and spin the dryer around so you can reach inside the vent door and pull the tension pulley over and reseat the drive belt. Rem

I unscrewed the old the lint screen FRAME and easily removed it, replacing it with the new one. The new lint -- SCREEN -- just needed to be squeezed here and there, and molded into a better shape. The screen itself, arrived flattened on the bottom, causing it to be too wide and difficult to remove from the frame. I easily molded it with my hands into the shape of the previous one and it slipped right into place. ( Shaped like an oval, flexible sack.) VERY easy!

First I unpluged the machine, then opened the top with a flat head screw driver. Then I removed the two screws inside, unpluged the door sensor. (makes it stop when opened) Removed old gasket, cleaned with emery cloth, cleaned the residue and applied the glue provided. Waited about 1 min. and applied the new gasket leaving about 1/8'' of it hanging over the door facing the drum.

For me it wasn't even a repair, but rather, open the package, take out and discard the old lint tray and pop the new one in! Done. I didn't have to replace the frame. I would like to comment on how easy ordering was from partselect.com and how quickly the part arrived. Very satisfied customer! Thank you!

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

1 Unplug the dryer and Raise top up by releasing the clips and fold back to expose the drum. 2. Take Phillips head screw driver and remove two screws inside the front dryer panel and then take flathead screwdriver to pop out both sides and set aside. 3. Lay on your stomach and reach inside to the belt pulley and push right so the belt will release then stand to either side of dryer and grab the belt and lift the drum up out of its bracket. 4. Go to the front and pull the drum out and replace the Rear Drum Bearing Kit . 5. Grab the front panel and remove the Top dryer guide and replace to match evenly with the bottom dryer guide by cutting at least 1/8 -1/4" from felt and use High temp adhesive to glue down. 6. Replace everything in order that was taken apart and reconnect electrical plug and start dryer.

1. unpluged the dryer and turned off the gas.
2. pulled dryer out so i'd have ample room to work on it.
3. used large flat blade screwdriver in the front between the top lid and dryer face to gently pop-up the lid.
4. removed 4 screws from inside, that hold the face to the main box leaving the wires all intact.
Found the coils on the lower left, held in place by two screws and plate.
5. took a good look at thier orientation before unpluging old and installing new, I recommend one at a time.
6. Vacuumm any exceess lint and check foam seal between lint trap and exhuast duc, the glue came undone on mine causing extra lint dust that is potentially flamable.
6. screw dryer front back on to main box, make sure to check wiring harness and that all electrical blade connectors are still pluged in to their componants.
7. At this point plug in, turn on gas and do a test run.
8.if everything checks out good then lower top make sure flexable exhuast hose is still connected on hte back of the dryer.
9. Tell your wife or girlfriend or husband or boy friend they can now finish your laundry :)

Popped the top of the dryer off. Removed 3 screws from lower front panel. Removed front panel slide belt over drum, remove 2 bolts from rear panel and installed belt over motor and around idler tensioner. Reinstalled front panel and top of dryer . Also greased idler pulley to shaft , beings tensioner was okay. Plugged in and tested dryer, it was okay.
We went to PartSelect. com and order the belt and it was fast shipping. We couldn't find the belt anywhere else. Thanks for PartSelect.

Removed 2 screws and dropped new screen holder in with lint screen in it and replaced screws. Really easy

After removing the front door of the unit I removed the Drum seal felt and upper felt part. Then I cleaned the metal ring with acetone to remove dirt. We you install the new parts the glue sent with the Drum Glide is enough for the task with a little left over. Now its working great.
Thanks for good part Jeff

removed two screws - replaced lint screen replacement, TIME TO REPLACE UNIT - ONE MINUTE. What made this project a snap was the pictures and graphs( parts replace) uses to ensure you are ordering the exact screen .

The appliance is gas, which made me a little nervous. However, knowing that I had the gas off, I carefully began disassembly. The burner unit is a very simple set up and within a few minutes I had the entire assembly out and noticed that in fact the igniter was broken. I ordered a new one from partselect.com and it was delivered in 2 days! The worst part of the assembly was when I accidentally bumped the new igniter against the underside of the dryer and broke the brand new one!!!..So, I ordered a second igniter and 2 days later installed it in about 30 minutes.

Before this fix which worked beautifully, I tried replacing the flame sensor which did not work. To read that story, search under part number PS459818 (Flame Sensor). Our model is a Westinghouse, so access to the unit is a bit different than the other stories. It's a stacked front-loader sitting on top of a washing machine.

1. Open the little front door (lower left side) by unscrewing the little screw right below it. The door will pivot and slide out vertically.
2. Disconnect the electrical main lead coming from the back of the unit (just in case).
3. Close the gas switch lever on main gas pipe coming from the back on left side (just in case).
2. Remove 2 phillips screws on top of the metal bracket holding the two coils. The screws have to be removed completely along with the bracket. It's easy, they are right in front and there is room for the screwdriver. Use a thin long one instead of one with multiple bits to better align with the screws, which are very close to the coils.
3. The two coils slide right out and are very different so it's easy to keep them straight. Remove electrical connectors before or after removing the coils (I marked the plastic on top with a sharpie to keep them in the right orientation).
4. Drop in the two new coils and reconnect them to the electrical leads.
5. Reconnect main electrical lead from back (match wire colors)
6. Reopen gas lever on gas pipe.
7. Drop in front cover at an angle, tilt vertically and put screw back underneath. Use magnetized screwdriver or a piece of scotch tape to hold the screw or it might fall off the screwdriver.
8. Voila'. It worked.

This website is great. Our dryer is a Westinghouse bought in 1991 (almost 20 years old!) and with this fix it's just like new. In 1994 we used parts bought here to fix our washing machine (Westinghouse LT350RXW1). That machine is now 15 years old and still going!