Models > 49-2828-23-02

49-2828-23-02 Tappan Dryer - Overview

Get Parts and Repair Help for 49-2828-23-02

If you know the dryer repair part you need, you can browse the list of all parts on the 49-2828-23-02, or you can search by name or part description. You can also find your part by where it is located on the 49-2828-23-02 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 49-2828-23-02 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.79

Rear Drum Bearing Kit

This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant and installation screws.

Order within the next 5 hrs and your part ships today!
$18.16

Upper Drum Glide

Front upper felt glide pad with 3 nylon glides - includes adhesive.

Order within the next 5 hrs and your part ships today!
$2.83

Drum Support Bearing

This part attaches onto the inside of the rear panel of the cabinet.

Order within the next 5 hrs and your part ships today!
$25.18

Door Catch

This part helps keep the door closed while the machine is running.

Order within the next 5 hrs and your part ships today!
$16.61

'M' Series Ignition Coil Kit

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

Order within the next 5 hrs and your part ships today!
$7.32

Door Strike

"Male" piece of a dryer door closing mechanism.

Order within the next 5 hrs and your part ships today!
$8.70

Bearing Bracket

This part mounts on the inside of the rear cabinet.

Order within the next 5 hrs and your part ships today!
$9.82

Idler Pulley Assembly

Use this idler pulley assembly with gas or electric clothes dryer that has a flat dryer belt. ***Please NOTE: This part has been redesigned by the manufacturer and may not fit your appliance.

Order within the next 5 hrs and your part ships today!
$26.06

Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

Order within the next 5 hrs and your part ships today!
$7.78

Flat Style Belt

This is a flat style ridgeless dryer belt.

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Loud Squeaking

  • Customer: Frank from Boyertown PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 262 of 270 people found this instruction helpful
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Acc... read more

Drum glide wore down and caused close to get stuck between drum and front panel.

  • Customer: William from Boise ID
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 167 of 232 people found this instruction helpful
Unpluged dryer. Removed the top of dryer by pushing in a retaining clip on both sides of the front lip with a screw driver. Remove the two screws on both sides of front panel. These screws are square head or phillips #2. Unplugged the wiring harness to front panel (make sure power has been disconnected). Support drum and lean front panel away from dryer ... read more

Dryer would heat initially then cool down

  • Customer: Brett from Monticello MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 55 of 61 people found this instruction helpful
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible... read more