49-2828-23-01 Tappan Dryer - Instructions

I followed the instructions in a Youtube video that an individual made with his kids. The only hard part was removing the drum assembly, the rear drum bearing was very difficult to unseat. I had to reattach the front of the dryer to give the drum assembly more support to be able to lift the rear - but overall it was quite easy to figure out disassembly and reassembly of the dryer. There's really not that much to them.

I followed the directions sent by you step for step and the rpair was done in no time at all. Had a little trouble with the roller ball installation but figured out how to install it after a couple of tries. Repair was done with minimal use of standard houshold tools.

It was easy, I handed the part to my husband and he did it!!!!!!!!!!!!!!!

Part Select got me the right parts in the agreed time--good job. Shut off the power or unplug the dryer which ever is easiest. The toughest part of doing this job was figuring out how the lid came off the dryer, if you have a jack knife or a putty knife you push it in between the top of the dryer and the body about an inch below the dryer top and about six inch from both sides of the dryer front you will hit a latch that releases the top--slip a screw driver into the opening and do the other side. The top can be removed or you can hold it open with a stick. There are two screws that you need to locate they are on the inside of the dryer front about 9" from the top one on each side they are all that hold the front on the body so remove them but carefully not to drop them inside the dryer. On my dryer there were two screw inside the dryer door that held the filter body onto the front that had to be removed too. Then push the screw driver between the front and the body of the dryer like the top and it will pop open. There are some wires going to the front from the body they can be unplug just follow the wires to the connection point. On mine, I squeezed the sides of the connector and the wires pulled apart. Now you can move the front aside. At the lower right in the body you find the valve and heater burner. On top of the valve there are two sets of wires coming off the valve. Disconnect the wires--one set is for a three wire connection the other for two wire connection. Your parts have a two wire coil and a three wire coil. The coils are freed by unscrewing the metal cover that holds them down remove the two screws and that cover then remove the old coil off the valve then replace the new coil with the part that is the same. Three pin coil with three pin coil positioning in the same way as the old coil, then do the other one. Reattached the metal cover with the screws and put it all back together in reverse order. The dryer chamber--the inside of the dryer rests on the front so when you put them together you may have to lift the chamber up to met the face a little (1/4"). Good luck.

The customer had removed the top cover hinges and the rear cover plate to recover the broken belt. I first removed the four screws holding the front panel and tilted it out to allow access for the new belt. The drum dropped about 2-3". Fed the new belt over the drum with the printing'This Side Up' facing me, lifted the drum up as I closed the front cover over the felt on the front rim of the drum. Replace dhtew four screws. Door switch leads were long enough to allow the front cover to tilt forward so did not remove. Next engaged the motor pully and tension pulley, then rotated the drum manually to assure tracking and no twist in the belt. Vacuumed the wall passthrough pipe,the flex vent tubing and the motor compartment of lint. Closed up the back cover and drove the 52 miles back to my shop.

The repair went very well.The biggest problem was the spring on the tension roller when putting back together.But it just takes a little bit of patients and it was fine.Works great now.

Referred to Video and replaced drum support bearing as shown. Did not solve the problem as noise was still present. Called professional repairman, who replaced the belt pulley, along with all the parts I had just installed (came as part of a total kit). I was on the correct path, but just didn't go far enough to check out the belt pulley. If it should happen again, I could complete the whole repair process. Great learning process!!

removed top-removed front-removed belt-removed drum (I didn't know how the drum came out WITH the bearing so I unscrewed the 3 middle screws on the back of the drum which released it from the bearing)- removed the bearing-that was when I knew what to order. installed the bearing on the drum before assembling all in reverse order. I wasn't sure how much grease to use so I used about 1/3 of it.

This repair took about fifteen minutes. I popped the top of the dryer using a flat-blade screwdriver, leaned it back against the back wall, unscrewed two screws holding the front panel, removed the five electrical spade contacts after marking which went where, swung out the panel and lifted it off. After that, it was a simple job to unscrew the plate holding the solenoids in, at the bottom left of the unit. I replaced the solenoids, closed everything up and now the dryer is working better than it has in the last three years, or so. If your dryer is heating sporadically, the odds are 85%, or more, that a solenoid swap-out will correct the problem.

Very simple. Pop the top open released the beld from the back it's easier that way the video was very helpful the sound was so bad you can hear it from a few houses down after year of just using it like that I figured I ha d nothing to loose great price great instructions now it sounds just as new.

Removed 2 screws from lint frame and replaced with new frame. Less than 2 minutes actually. Dropped in new lint basket and ready to go. Part arrived faster than expected. Website very easy to use. So pleased !

I viewed the video from your site (Parts Select's) and followed those directions... which took the guess work out of the job and made it simple. Also the video alerted me to small ball bearing in the back which might have caused some head scratching if not for viewing the video. While everything was apart I did spend extra time cleaning. Many THANKS to Parts Select and the courteous parts person that I spoke with and placed my order with.

after watching the video,I followed its instructions. No surprises No problems

Pulled dryer forward for access. Raised top by pressing clips on front. Removed front panel 2 screws. Removed old felt flange with plastic guides. Cleaned surface of old glue. Dried. apply cement per instructions applied new felt. New fit was snug and required some manipulation. When in place it helped to hold felt until cured. works great. Would not have known what problem was without the videos @ Part Select. Thanx for info and part. David

It was really easy to install the new roller with the newly designed side flange! All I had to do is hook in the tension spring. Works perfect again without the squeeking noise!