Models > 4790 > Instructions

4790 Jenn-Air Range - Instructions

All installation instructions for 4790 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 4790
46-60 of 82
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

needed new grease filter

  • Customer: Barbara from Hubert NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 1 people found this instruction helpful
It was hard. I simply replaced the old one!! fIT PERFECTLY.
:-)

range handle fell off and screw got lost

  • Customer: Frances from palm beach gardens FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
It was worth the money for that little screw, since I didn't have to run all over trying to find the right one.

bake element not heating up

  • Customer: john from chatham MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 2 people found this instruction helpful
removed element and tested wirh ohm meter. No reading telling it was bad. Tested voltage from supply wires. Voltage correct. Ordered new element which can in 2 days. Installed-tested- problem solved. 2 scres connect element.

Oven element burned out

  • Customer: Eugene from Satellite Beach FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The only trouble I couldn't remove the screws that held the wires to the element, so I cut the wires as close to the end as possible and attached new hardware. After that was done it was simple to reinstall the new element. Turned the power back on. Turned the oven on and it worked like new.

The stem of one of my burner switches broke off so I had to replace the switch.

  • Customer: John from Fulton NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 0 of 2 people found this instruction helpful
Replacing the switch was very easy. First I unplugged the range to be sure there would be no electrical power to the switch. Then I removed four screws to remove the switch cover plate (located above the oven door). I disconnected the wires from the pin connectors on the broken switch, then removed the switch by removing one hex nut. The new switch was installed by reversing the removal procedure. Took about 15 minutes total time.

missing clock knob

  • Customer: Jimmie from Hampton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
placed knob on clock shaft with my fingers

parts fine,

  • Customer: MARY from ELK RIVER MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
just inserted in to proper place

replaced the current warn-out grease filter

  • Customer: Joseph from East Greenwich RI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
removed the old by pulling it out of track and replaced it with the new filter

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

The filter in the grill section of my stove fell apart.

  • Customer: Beth from Dunkirk NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
I simply removed the old filter and replaced it w/the new filter. It came in record time and I'm very pleased w/the service I received.

the original grease filter was worn and falling apart

  • Customer: Barbara from Medfield MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 3 people found this instruction helpful
Removed the old filter from the top of stove and put the new one in. Took about 10 seconds.

lower element was burnt out

  • Customer: JOSEPH from WARRENTON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 4 people found this instruction helpful
same as your example

Old grate were nasty

  • Customer: Greg from Ortonville MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I actually bought these for a friend. He cooks for everyone that shows up. I haven't seen the new grates in action yet. Will have to show up with some meat and test them out.

Surface burner did not heat

  • Customer: james from Santa Claus IN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I ordered part one day, recieved part the next day. I installed it the next day. It worked perfect. THANK YOU!

Both burners would come on when you turn on the back larg back burner.

  • Customer: Jerry from Tallahassee FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced surface unit infinite switch
All Instructions for the 4790
46-60 of 82