47-2848-23-03 Tappan Dryer - Instructions

I watched the great easy to follow video from PartSelect. Absolutely nothing unclear. I was able to open the top and disconnect the front panel in less than 10 minutes! Removed the old felt drum glide, scraped off any stuck felt and loose glue. Then glued the new pad in place, using 3 small clamps, like clothes pins. Let it set for about 15 minutes then put it all back together! I did forget to reattach the ground wire, so I had to open the lid back up for that. About 50 minutes total. Also I took the opportunity of having the front panel off to give the inside a good vacuuming, not a ton of lint but enough to go ahead and clean it out! Thanks for the help!

Popped top off with flat head, took 2 screws out with phillips head, disconnected wiring, took front off, old piece removed, cleaned with razor blade, installed new glide, all done. I am sorry I waited so long to try this. So easy!

It was super easy! I followed the PartSelect video and everything went fine. Getting the drum out of the machine was a bit tricky but once it was out, the rear bearing kit went in without any problems.

1. watched PartSelect video 2. adjust for the fact this was a dryer over top a washer. 3. we were able to remove the very top plate of the dryer and not have to remove the drum to get to the Thermal Limiter. 4. i used a drill driver with a square bit to speed up getting out screws. 5. It requires a ladder to be able to work from the top and 6. some pretty good manual dexterity to get the limiter out without removing drum. 7. the replacement seems to have improved the drying function!

I watched the videos on this excellent website first. Then the repair was a breeze.

I followed the instruction video and easily removed the drum. Mine is a gas unit, so the best access to loosen the pulley and belt is by removing a small hatch on the back of the dryer. Removing the ball shaft was initially difficult, since the screws had been stripped by the previous repair person. To solve this, I used a vise-grips to turn the protruding shafts of the screws at the drum rear, and unscrewed them partially out from behind. Once loosened, I used a screwdriver to easily finish them. The old bearing was actually gouged, and there was no lubrication at all in the retainer cup. The job took 2+ hours, since I also replaced the upper felt glider and spent 30+ minutes vacuuming the dryer out.

installed the back bearing with the ball bearing and dropped in the rear drum bearing and tried to install the drum to the rear drum bearing, but we could not find the screw holes to attach the drum, we tried and tried and finally I came up with the idea to take the drum out and screw the drum bearing while we had it ouside and that worked out beautifu lyl and all we had to do was reinstall the drum and all we had to do was lift it up just a little and drop it into the retainer rear retainer' and then all we had to do was install the tension roller which we had a little trouble but we finally figured it out and now it works just fine, it would a lot if there was a diasgram included on how to re-install the tensioner

This video by Steve Ash was spot on . In our case the white rear support bearing had melted and reformed around the shaft, preventing us from being able to pop the drum in the way described in the video. We used pliers to unscrew the screws on the rear clip from the back of the dryer. The rest of it worked exactly as described in the video. Our model was White-Westinghouse DE600ADD1, which is not a model listed on the PartsSelect website. However the part worked very well. The dryer runs really quite now.

watched the video My dryer was a little different but it came apart easily and was an easy fix. My wife did it all by herself.

Replaced the guide pads. they were slightly different. I was able to modify them. I think it'l be fine

The repair video from PartSelect.com was excellent in describing how to fix the dryer. All of the parts were included in the replacement kit, including the screws and ball bearing. I was very impressed with the quality of the kit and the video. A $25 kit probably saved me hundreds in repair cost and saved me from having to buy another dryer. Here's to another 14 years of use!

Ordered the part from PartSelect.com. It came in a couple of days, which was nice. My wife was all over me to fix the dryer, or buy a new one. Needless to say, I didn't think the old one was done. The bearing assembly had an instructional video. This provided easy to follow instructions, and simple advice even I could follow. Everything went well, and the dryer is now quietly running as good as new. Awesome website, and the customer service is excellant too. WE use PartSelect.com at work all the time. Im a property manager, and the parts and advice save us thousands every year. Thanks guys!

Disconnected and moved the unit outside, just to clean the lint out of it. Removed the top, then two screws holding the front panel on. Disconnected the two door switch wires. Peeled off the old upper seal and cleaned surface with wire brush. Applied the supplied glue and clamped the new drum guide in place. While it was setting up, I cleaned out the entire inside of the dryer to eliminate the old trapped lint. Replaced the front panel and mounting screws. Reattached the wires and closed the top. Relocated back inside and plugged it in and reconnected the vent tube. Turned it on and it worked perfectly.

when the bearing broke the drum fell in the back. I tore the dryer apart, ordered the part and fixed it when the part came. the dryer runs like new now!

I used the video, and it helped me a lot! I got the drum out, installed the new bearing, greased the new shaft and the receptacle, then I reassembled. When I tested it, mine was still very noisy, so I removed the drum once more and cleaned/added some grease on the tensioner bearing. This was the cause of the noise in my case, but the bearing & housing were nearly shot, so something would have given out very soon. I would suggest to grease the tensioner the first time to save time and effort. (And save some of the grease for the tensioner pulley). SAFETY TIP: there was also a ton of lint that got trapped inside the unit!!! Clean your dryer once per year to prevent it becoming a fire trap!