47-2828-00-03 Tappan Dryer - Instructions

The consensus seemed to be that the loud squealing was most likely the rear drum bearing needing to be replaced. Although the repair went very well (great video!), it did not fix the problem. BEFORE you go the route of replacing the rear bearing, first pop up the top and see if a little piece of plastic that is attached to the top middle of the front panel by a screw is rubbing against the drum (you have to have a load going). I removed this part (I could not find it listed on any parts list) and the squealing stopped. I have no idea what the purpose of this part is, except for maybe keeping the drum from dropping too far down if the load is really unbalanced. This plastic part is on the dryer that has the controls on the front (it has the ability to be stackable) and might not be on the other unit that has the controls on the top back. If anyone has posted this as a possible cause of the squealing, I haven't seen it.

First I like fixing things for myself. So I looked the problem up on the internet. Found the repair tech that I needed. The found your parts site. And BOOM. Looked up mt part on your site. Very easy you had everything I needed. And you got it to me quick. THANKS. When the part hit my mailbox. Everything I needed was there. I pulled the plug. Fliped the lid up. Took off the front. Removed belt off the ideler. Removed drum replaced bearing assy. Put it back together. Closed the lid and pluged the unit in. Worked so well I felt like a pro. My wife was tickled pink. Just like a new one. Thanks guys for making me look good and saving me a lot of money. Will use this site again. I give you 2 thumbs up.

I ordered the rear drum assembly on Monday evening and the part came on Wed at 11 am. I started the repair at 1 and finished at 3. It would have been faster, but my computer kept freezing during the repair video. The video was so easy to follow. I could have used longer arms or a helper, but I managed to get the job done by myself. Needless to say, my husband was thrilled. Great service. Thanks

Repair went just according to the video except to pull the drum out there was a plastic lock at the front of the dryer. It was held in by one screw and easy to take off. When I pulled the drum out the armature and spring that hold the belt tight fell off. I panicked a little, but easily put the pieces back in place. When I started the dryer for the first time it sounded odd but realized it was the sound of all the grease spreading itself around the bearing.

I followed your videos.Last year I changed the dryer belt with help from your video.Your videos on each repair I've done have been absolutely priceless. You have made every step so clear and easy. Thank you to everyone involved with your DYI program!!!

Used wiring diagram in back of machine control head. UNPLUG DRYER! Removed panel off control head and motor access cover at bottom of dryer. Tested door switch continuity first, then continuity from control timer to motor. Found open circuit on white wire. Opened top of machine (pops up at front) and found thermal limiter on back of machine was burned and caused open circuit. It's a little awkward to get to the screws with the drum in place. Use a 30º angle ratching 1/4" ratchet wrench with a magnetic #2 phillips bit.

Remove small back plate near floor with 1/4 inch nutdriver unscrewing two screws. Lay the small plate to the side. Remove dryer belt from around pulleys by pulling up on the old idle arm near main spring. This will loosen tension of the belt. Belt just needs to be removed from only around the two pulleys. Detached spring from old idle assembly. The old assembly will just lift out. Reassemble in reverse order with new assembly from Parts Select. Takes less than 5 minutes. Extremely easy!

THE PROBLEM: Rust marks in the shape of a V started appearing on my clothes. I finally realized that there was gap at the bottom between the drum and the outer frame that was caused by the upper drum support having deteriorated... Clothing would slip into the gap into the area where the metal of the spinning drum was exposed - then spin upward leaving a small rust mark... INSTALLATION: The video of installing this product was spot-on! I removed the old glide and residual glue (the glue was the hardest part), then put the new glide on. After the glue dried enough to hold the felt in place, I put it all back together. So far, no more rust marks on my clothes!

lifted up the top after releasing 2 catches with the putty knife, removing front panel, held in place with 2 screws. Scrape off top felt strip with the worn teflon tabs. Wire brush off old glue. Apply glue provided.(thin coating). install new felt strip. let the glue dry for a few minutes, reinstall, and you are done.

I got my order THE DAY AFTER I ORDERED IT!!!! I didn't expect that. If you can use a screwdriver you can install it. I would use this company again for anything I needed like this. Great service!!!!!

I removed two phillips head screws, lifted out the old screen and frame, dropped the new frame and screen in place and replaced the two screws. Total time to repair was less than 90 seconds.

took front off machine removing screws. Removed old felt and cleaned old glue off making sure area was clean. applied new glue and then new felt drum glide. put fish sringer around complete drum pulling tight clamping with vise grips till dry. then put front back on machine.

Had the macnine apart before ordering the Bearing Assembly. Reading other comments convinced me to order the Bearing Assembly. Parts were shipped very quickly after ordering and following the instructions on the web site things went back together easily.

I watched the videos provided on this website and followed the instructions in the order confirmation e-mail. These were both very helpful

Replaced rear bearing on back of dryer. Repair cost $20.00 an a little time. Much better then buying a new dryer. It was easy to repair the video instructions were great. I would do it again it needed.