Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 46-2830-23-02 > Parts

46-2830-23-02 Tappan Washer - Parts

All parts for the Tappan Washer 46-2830-23-02

Below is a list of all parts for the Tappan Washer 46-2830-23-02 - 27". To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 46-2830-23-02
1-14 of 148
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the water inlet valve is in any way damaged or defective, it may be slow to fill or even leak. Before beginning this replacement, make sure to unplug the washer from the power range or shut off the house circuit breaker. Remember to wear gloves for safety. Refer to the installation instructions and the diagram provided by the manufacturer for best results and accuracy.

$9.35

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell...

$6.67

SCREW

Sold individually.

$30.44

Agitator Drive Block

The agitator drive block rotates the agitator assembly in your washer. If the drive block breaks down due to wear and tear the agitator will stop working. If you notice that your w...

$24.25

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace the snubber ring. Because the snubber ring is located under the tub of the washing machine, you will need to remove the front panel to access it. To protect your hands when removing the snubber ring, consider using a bent coat hanger or a sturdy wire with a hook to pull the old snubber ring free. Be sure to disconnect the power and water sources for the washing machine before you begin this repair.

$48.78

Spin Bearing

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, theref...

$8.78

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. This part goes between the timer knob and the dial in a washer to function effectively and provide protection. The length of this part is 6.35 inches with a width of 5.25. The spacer has a height of 8.125 inches and the weight of 0.3 pounds. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to unplug your appliance from the power source.

$60.27

Agitator

$8.47

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

$8.47

SPRING

$29.13

Horizontal Spring

This is a horizontal spring, but you may know it as a suspension spring, and it is a part for your washing machine. Its function is to stabilize the outer tub by keeping it balanced. In order to make this repair you will need a putty knife, and a Phillips head screwdriver. This spring is roughly 1 inch thick by 4 inches long, it is chrome colored, and has two hooks on either end to make your repair easier. Take note that this piece is sold individually.

$30.10

Splash Cover Seal

The tub ring seal or splash cover seal is used for washers. This part seals the tub cover to the outer one and prevents water leakage from around the tub ring. If your seal is dama...

$29.47

Tension Spring

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if you notice that your washer is not spinning or agitating, the drive belt has come loose, and the idler pulley is no longer secure. To access this part, you will need to remove the front of your washer. The spring is located underneath the bottom of the tub. This is a genuine OEM part that comes right from the manufacturer.

All Parts for the 46-2830-23-02
1-14 of 148