Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 46-2251-00-03 > Parts

46-2251-00-03 Tappan Washer - Parts

All parts for the Tappan Washer 46-2251-00-03

Below is a list of all parts for the Tappan Washer 46-2251-00-03 - 27". To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the 46-2251-00-03
1-14 of 139
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

$5.56

Screw-In Plastic Leveling Leg

This is a screw in leveling leg for your washing machine. It supports the appliance by screwing in place to create a stable and flat surface. Take note that you are able to adjust the height of your appliance to make it leveled. This model is made entirely of plastic and is white in color. It is just under 2.5 inches long, 1.5 inches wide, and the head has a diameter of roughly 1.5 inches.

$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$9.35

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need to replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

$6.67

SCREW

Sold individually.

$24.25

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you may need to replace the snubber ring. Because the snubber ring is located under the tub of the washing machine, you will need to remove the front panel to access it. To protect your hands when removing the snubber ring, consider using a bent coat hanger or a sturdy wire with a hook to pull the old snubber ring free. Be sure to disconnect the power and water sources for the washing machine before you begin this repair.

$48.78

Spin Bearing

The spin bearing, used for your washer, is located at the bottom of the outer tub near the transmission. The spin bearing carries the transmission shaft in the drive system, theref...

$8.78

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. This part goes between the timer knob and the dial in a washer to function effectively and provide protection. The length of this part is 6.35 inches with a width of 5.25. The spacer has a height of 8.125 inches and the weight of 0.3 pounds. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to unplug your appliance from the power source.

$8.47

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for t...

$8.47

SPRING

$29.13

Horizontal Spring

This is a horizontal spring, but you may know it as a suspension spring, and it is a part for your washing machine. Its function is to stabilize the outer tub by keeping it balance...

$29.47

Tension Spring

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the tension spring is if you notice that your washer is not spinning or agitating, the drive belt has come loose, and the idler pulley is no longer secure. To access this part, you will need to remove the front of your washer. The spring is located underneath the bottom of the tub. This is a genuine OEM part that comes right from the manufacturer.

$19.35

Agitator Cap Seal

$39.69

Water Inlet Hose Assembly

This water inlet hose is used in washers. The hose connects the washer water inlet valve to the water supply in your home. There are two solenoids on the valve, which are referred to as coils, and there are two wires attached to each solenoid that should be labelled to ensure they are properly reconnected after replacing the new hose. Over time, your hose can begin to leak which can lead to floods. Replacing your hose earlier on can prevent this problem. Refer to the diagram provided by the manufacturer for installation instructions. Remember to unplug your appliance from the power source before beginning this installation project.

All Parts for the 46-2251-00-03
1-14 of 139