46-2251-00-01 Tappan Washer - Instructions

did the repair from the video that you had supplied for me. Thank you so much for making this one repair that was so easy and for your great customer service.

removed two screw at the bottom of front panel and pulled down on panel to remove, determined water coming out splash seal, splash cover held on with plastic clips around cover. Removed two screws on back side of top and hinged top over removed splash cover and cleaned old seal out replaced with new seal.Simple job but could not find parts locally and found Partselect on internet and ordered parts, very friendly and knowledgible person, ordered parts and had them in three days, would very highly recommend. Thank You Joe Lumpkin

Watched the handy-dandy video, removed the defective part, waited for delivery, installed the new part and was back washing another load (minus the wet floor) in less than 10 minutes! Just one catch, I am a 56yo female with nominal hand strength, so technically, I had to recruit the help of a (stronger) person to tighten-up those self-tapping screws. I didn't feel so weak when I noticed that he had some difficulty as well. LOL! Ladies, don't be shy asking for help-I even tried the power drill with no success. Excellent video! Aside from the self-tapping screws, my grand-daughter could have managed this repair!

For the washer/Dryer combo, replacing water valve was easy, first you need to remove washer front panel and top lid, make sure that washer electrical is unplugged, turn off gas, turn off water valves.remove 1-screw holding water valve. reaching from top and using pliers remove retention clip holding hose. remove old water valve, there are two electrical connections for cold and hot water valves, make sure you mark them, remove them from old water valve. insert new water valve, connect hose and make sure that retaining clip is connected correctly.connect electrical wires. screw water valve into place from rear of washer. connect water hoses. before connecting panel and lid, turn on water valves and observe if there is any water leaks.

Took off the front panel and changed the belt. Putting on the front panel took longer then changing the belt.

remove old belt, install new belt

I used a flat-head screw driver to lift the main lid up off the washer to get to the washer lid safety switch..Unplug the plug from the electrical outlet. Removed the 4 wires from the switch, and removed 2 screws to remove the old switch..Then install the new safety switch in reverse order.

I turned off water valves. I then unplugged the AC. I took the 4 screws out on the back end of the top cover of the washer. I removed the two water lines from the water inlet vales and the two electrical connectors. I then removed the two screws holding the water valve assembly and it came out easy. Installed new water valve assembly mounted with two screws , then put the electrical connection and water lines back on new water valve assembly. I turned the incoming water vales on and installed the top cover with the four back screws and was done.

Following the easy instructions on PartSelect's website, I first removed the screws from the bottom, front of the washer. Then, using the putty knife, I unhooked the clips holding the washer top to the front and pulled off the front. I pushed in the belt wheel and removed the old belt, which was being held on by one strand. Then, I put on the new belt, put the front back on, replaced the screws and then pushed the washer lid back down over the clips. It worked perfectly and took less than 15 minutes and cost me next to nothing. Thanks for a great site!

followed on line instructons very easy

Have you spouse take the washer apart and fix it. He did it in no time.I was able to order the parts and have them shipped. They where here in no time Thank you PartsSelect.com

Remove the agitator and the 2 bolts that clamp the spin drum to the shaft and pull up on drum the 2 seals are on the shaft right there. Pry up on the seals to remove them. Install all seals and Be sure to completely clean all parts before putting them back in the machine and re assemble the machine. The bad part of this job is if you have used powdered soap it took 3 hours to clean the parts before reassembly.

watched the video on website, printed instructions for feedback.

Used a metal cooking spoon to pry open the lid, held it in place with a chain (mentioned in the tools required) and used needlenose pliers to remove the clamp on the old hose assmbly. Transferd that clamp to the new hose assembly and replace the (1) screw holding it in place. Closed the lid of the washer, and now it is like the problm had never existed. (Very easy fix, 1 of 10 on difficulty scale).

I removed the back cover after disconnecting the electric and shutting off the water. I then proceeded to disconnect the water lines and then removed the water inlet valve by removing the two screws holding it in place. Then I used pliers to remove the hose leading to the washer. After that I did everything in reverse and was back in business. The video was very helpful and it made me feel comfortable with the procedure. I now know a little more about washers. Thanks for the excellent information.