Models > 41748106700

41748106700 Kenmore Washer - Overview

Get Parts and Repair Help for 41748106700

If you know the washer repair part you need, you can browse the list of all parts on the 41748106700, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 41748106700 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$68.60

Door Lock and Switch Assembly

***NOTE: As per the manufacture, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would requir...

$30.82

Door Striker

This part is found on the door of your washer and keeps your door closed for use.

$100.35

Drain Pump - 60Hz 120v

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

$169.50

Bellow Kit

Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. ***NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.

$5.27

SCREW

$29.11

Drain Hose

Also known as tub-to-pump drain hose.

$16.73

Spring-Held Bellow Clamp

$58.14

Dispenser and Water Inlet Valve Assembly

$33.87

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

$5.20

Comb Flat Head Screw 8-18

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 196 of 234 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

Old Bellow Ripped

  • Customer: Peggy from New Castle PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 130 of 177 people found this instruction helpful
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside ... read more

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 73 of 88 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes l... read more