Models > 3XLER5437KQ3

3XLER5437KQ3 Whirlpool Dryer - Overview

Get Parts and Repair Help for 3XLER5437KQ3

If you know the dryer repair part you need, you can browse the list of all parts on the 3XLER5437KQ3, or you can search by name or part description. You can also find your part by where it is located on the 3XLER5437KQ3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. We’ve also included any installation videos we have for 3XLER5437KQ3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$12.77

Thermal Fuse

This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when continuity between the pins...

$4.06

Door Catch Kit

This dryer door latch kit comes with one plastic door latch and one metal door strike.

$16.97

Door Switch - 3 Wire

A door switch is a simple on/off mechanism that prohibits the dryer from operating when the door is open.

$24.54

Lint Filter

This filter collects lint as it passes through the dryer vent.

$16.63

Idler Pulley with Tri-Ring and Gasket

A dryer's idler pulley helps the belt to rotate the drum. Also known as dryer belt tension pulley wheel.

$4.46

Thrust Washer

$38.92

Dryer Repair Kit

This kit comes with one multi rib belt, four drum support rollers, one idler assembly, nine tri rings and one washer.

$29.45

Thermal Cut-Off Kit

This kit includes one high limit thermostat with a limit of 250 degrees Fahrenheit, and one thermal cut-off fuse with a limit of 360 degrees Fahrenheit. The thermostat and fuse help prevent the dryer from overheating.

$3.46

Leveling Foot

Sold individually.

$16.65

Multi Rib Belt

This dryer drum belt from Whirlpool/Kenmore has five ridges. It is used for many of Whirlpool's brands of clothes dryers. This flat belt is 1/4 of an inch wide.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer was working, but no heat.

  • Customer: ANTHONY from CHESHIRE CT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 1045 of 1199 people found this instruction helpful
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, ... read more

door switch was bad

  • Customer: pat from lisbon, OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 509 of 511 people found this instruction helpful
i was able to go on line with your company , find my dryer, order the part and had it the next day. fast , great , service read more

No heat but would run otherwise

  • Customer: Dana from Grassvally CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 500 of 509 people found this instruction helpful
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and didn't take but 15-20 m... read more