Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 3XKVN490000

3XKVN490000 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 3XKVN490000

If you know the refrigerator repair part you need, you can browse the list of all parts on the 3XKVN490000, or you can search by name or part description. You can also find your part by where it is located on the 3XKVN490000 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 3XKVN490000 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$7.60

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$7.20

Touch-Up Paint - White

18ml

$35.17

Light Socket Kit

The bulb is sold separately.

$11.64

Ice Pan

This part may come in white or clear plastic, but either will still work and fit properly in your appliance.

$100.45

Fresh Food Door Gasket

This white door gasket is used to seal the refrigerator door when closed to keep the cool air inside and the room air out.

$11.07

Spray Paint - 12 oz. - White

$31.47

Roller and Eyelet - Kit of 2

$10.01

Egg Container

This part is used to hold eggs.

$6.60

Touch-up Paint - Black

16ml

$5.00

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 102 of 111 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 90 of 108 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover whic... read more

No ice in ice trey

  • Customer: Wayne from Leesburg, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 70 of 82 people found this instruction helpful
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and star... read more