Models > 3XKGN705000

3XKGN705000 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 3XKGN705000

If you know the refrigerator repair part you need, you can browse the list of all parts on the 3XKGN705000, or you can search by name or part description. You can also find your part by where it is located on the 3XKGN705000 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 3XKGN705000 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.82

Door Cam

Note: As per manufacture a new screw is needed to mount door cam. Sold individually.

$27.33

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$23.19

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$10.86

Door Closing Cam Kit

This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.

$9.06

Micro Switch

$3.76

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

$2.70

Screw

This screw is sold individually.

$3.96

End Cap Trim Piece

$20.61

Shelf Support Stud

This is a 12 piece kit.

$11.34

Shelf Support Stud - White

This kit contains two options - One that is a push and turn and the other that is a screw in.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Plastic bits dispensed from Ice Dispenser in Door

  • Customer: john from seaford VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 111 of 121 people found this instruction helpful
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws ... read more

The door would not close properly. The CAM had broken.

  • Customer: Thomas from San Clemente CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 93 of 95 people found this instruction helpful
The repair was very simple.

1. Remove the food from the door shelves.

2.Remove the door by first removing the three screws holding the hinge at the top of the refrigerator.

3. Lift door off of the bottom hinge.

4.Replace bottom CAM on bottom hinge (one screw)

5. Replace top CAM and shim on door (one scre... read more

Fridge was getting too warm, ice buildup on coils.

  • Customer: Cathy from Winter Park FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 81 of 89 people found this instruction helpful
WARNING: REPLACING THIS PART REQUIRES CUTTING AND SPLICING ELECTRICAL WIRES. RISK OF ELECTRICAL SHOCK OR FIRE. DO NOT ATTEMPT THIS REPAIR IF YOU ARE NOT EXPERIENCED WITH ELECTRICAL WIRING.

Part Info:
The bi-metal strip is clipped onto the evaporator coils and is designed to regulate the defrost coil temperature. If it is not functioning prope... read more