Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 3UMTW5755TW0 > Instructions

3UMTW5755TW0 Maytag Washer - Instructions

All installation instructions for 3UMTW5755TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3UMTW5755TW0
46-60 of 221
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer tub off balance and noisy

  • Customer: Gregory from Kent, OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 6 of 6 people found this instruction helpful
The repair was fairly simple and while it made the spin operation quieter and and a bit more stable, it still gets out of balance. Disconnected power, shutoff supply lines and disconnected them from the unit.

Laid washer on its front and replaced the two more visible springs fairly easily from underneath using a little leverage with a 2 x 4 to take any residual tension off the springs.

Then I turned the washer over on its back (gently and with a little support (board or old thick towel) so the weight of the unit didn't rest entirely on the water intake connectors

Again, lifted the tub with 2 x 4 and disconnected the power and control connector to the motor to make a little more room to get to the spring.

If you do this, be sure to re-connect that connector before you put the washer back and test, otherwise it will fill and then sit.... I had to siphon the tank out, disconnect everything, flip it over and re-connect that power connector!! After that the unit ran better than before, especially on the spin cycle. Over all this washer is 15 years old and worn a bit so we are still careful not to overload it and balance the loading as much as possible. Large bedspreads and king size sheets or mattress covers will always spin out of balance but for 90% of regular washing it was an improvement.

Broken water inlet syphon combined with missing feet was causing water to spill out of the washer

  • Customer: Randy from Atlanta, GA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
  • 13 of 28 people found this instruction helpful
I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

hoses had holes in them

  • Customer: Sharon from Dallas, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
Put clamps on hose end and then used some dishsoap on the inside of the hose to make pushing them into place easier once in place I placed the clamp in correct spot and used a screwdriver to tighten the clamps.

shaking on spin cycle

  • Customer: Paul from Milwaukie, OR
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.

timer knob broken from support at base

  • Customer: RISHIE from LITTLE FALLS, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 8 of 15 people found this instruction helpful
with pliers removed remaining broken part on selector switch
attached new knob sliding fool proof groves on innerside now we are back in business, myself and family thank you for the support

drain hose for washer was cracked and leaking

  • Customer: richard from orange, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 9 people found this instruction helpful
This was really easy and the part came in like 2 days. All I needed to do was flipthe washer on its side and remove the old hose...a couple screws and install the new one...it was a perfect match so ...no issue.

Washing machine shakes violently during spin cycle

  • Customer: James from Asheville, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 17 of 42 people found this instruction helpful
Removed four screws that hold the top control panel to the base and hung over the back panel in order to remove the main wrap-around body of the machine. Took off top plastic ring fastened to side of tub then removed old Balance ring. Installed new balance ring. Unfortunately, this did NOT fix the problem. This was a suggestion from Justanswer.com and failed miserably. Does anybody know how to fix this problem? And it's not the springs or the little plastic shims around the base OR the cross coupling to the motor...

Retainer clip for the pump missing, caused pump to fail

  • Customer: Matt from Roca, NE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 4 of 4 people found this instruction helpful
Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

washer shakes and was very noisey

  • Customer: william from lindside, WV
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

Leaking discharge hose

  • Customer: wayne from webster, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 7 of 13 people found this instruction helpful
removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

drum SLAMMING into the back of the washer when sipnning

  • Customer: WILLIAM from DAYTON, KY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 4 of 5 people found this instruction helpful
I just replaced the spring just like the vid show me.it run's like a new one-I bought it used about 5 yr's ago

Washer lid seal replacement

  • Customer: Kathleen from Ocala, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Ordered the part, received part in short time and snapped it on in less than a minute. Seals better than original.
Thanks PartSelect. I will be back.

slow or no spin

  • Customer: Steven from Wausau, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 6 people found this instruction helpful
First read up on what others did and tried to find free repair manual with little luck. Called repairman, they thought whole transmission was shot- would have been $70 just to have them look- forget it. Getting it apart: popped off the two console cosmetic panels to get to a screw on each side from the top. Lifted off console, levered and squeezed retaining clips. Unhooked two connectors and overflow tubing? Shell pulled off easily, getting back on after I was all done made me wonder if it was a good choice. In the end yes- allowed me to clean inside surfaces of both tubs to remove grime and rust. There are many stories on the actual clutch replacement, so won't go into too much detail but some lessons learned. Keep track of the way all the plastic aggitator pieces go in, plus the washers and clips along the way. Deep well 1/2" I think socket for the tub, it's litely spring loaded so look before you set it down. Punching off the nut on the tub worried me, but it was no big deal. Loosens and tightens the normal directions, no positive tight stop, just compression so pay attention to how tight and hard you pounded to get it off. Drain the water from the inner tub before getting too far. I took the four springs off and removed both tubs to clean. No more complaining about brown spots on clothes. Get the whole clutch kit, not just the band, even though it's probably just the band worn out. The plastic clutch engaging piece will probably be fatigued. The motor etc is heavy, and buffered it's drop with rags. tip on side when putting it back, because its a bear to try to lift up. I lightly greased some moving parts, just not much as to not cause band grip problems. The wire retaining clip is tricky- I put the hook end in first, used pliers to try and compress, and screwdriver to push down and in. The whole things wants to spin while you do this, but when it finally goes, it stays. I was concerned about the location of the band spring in relation to it's actuator when putting it together, but it turned out if you put it anywhere where the clutch is free to spin, it will engage normally. The top lid has two rubber bumpers, one fell off and landed on the front bottom corner of the cover which didn't help reinstallaion until my 8year old noticed it! Took a number of tries but finally got the four guides from the frame into the cover. I tried bringing it in level, front tipped sligthly up, front tipped slightly down; in the end I won't be much help, it just finally went. It wasn't as easy as most people said it would be, but my back hurt and I had kids "help", and it took just under two hours. Works amazingly well now. Parts arrived Two days after ordering, with no expiditing!

Kenmore Series 80 Lazy Spin

  • Customer: Robert from Henrico, VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 4 of 6 people found this instruction helpful
Remove metal cover; remove pump, remove motor, remove tub spin assembly; remove transmission. Remove clutch be removing retaining ring. Installation was reverse. No problems, part worked like champ.

Note: Called Sears to see if I could get the part locally. Turns our I had to call an 800 number. Lady said that the part was not carried and would have to be shipped from warehouse. Tried to sell me some discharge hoses. Then said the part would cost $65 before S&H. Told her I didn't want to spend that much, she asked how much I wanted to spend and seemed upset when I told her your price. She didn't comp it, just said that theirs was an official part from Sears, blah, blah, blah. Anyway, thanks for the great service!

washer would walk all over when in the spin cycle

  • Customer: Chris from Bonners Ferry, ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I tried to remove the outer console to get to the tub wear pads easier. This proved difficult for me for some reason. So I tipped the machine on its back at about a 45 degree angle. You will see the tripod support holding up the tub. The pads lie in between the bottom of the tub and on top of the tripod support . You won't be able to see the pads since the are on the top of the support, but you will see the two insert tabs of each pad sticking out. There are about 120 degrees apart from each other. I pushed up on the tub and slipped the piece of wood in between the tub and tripod support close to the pad. Taking a screwdriver and hammer I punched out the wear pad insert tabs. You can replace the old pad with the new one by using some force with your hands. Some pop right in and some you need to use a little leverage, maybe with the piece of wood you used to hold up the tub. Be careful not to get the pads greasy, keep clean as possible. Worked great.
All Instructions for the 3UMTW5755TW0
46-60 of 221