3UATW4605TQ0 Admiral Washer - Instructions

Unplug power from wall.
Disconnected water lines
Tip Unit on it's side. (Recommend turning so motor is to the top side)
Disconnect Electrical connector and Hoses from the pump and motor.
Disconnect metal straps used to retain the motor to the transmission. (screwdriver to pry)
Remove old coupling pieces from transmission/motor(used a long screw driver, rock back and forth)
used air compressor to clean up electric motor
replace new coupling on motor and transmisison (may need hammer to tap into place)
set rubber bushing on transmission side (transmission shaft should be facing up at this point)
replace electric motor into place, making sure to line up bushing and motor mounts.
replace metal strap connectors between transmission / motor (this can be tricky, as the one in the back is hard to get at.)
replace electrical connectors and hoses
connect washing machine power and water and test

Removed capscrew in end of agitator shaft took cover off machine-[ unscrewed two screws holding down control panel, hinged back, pryed retaining clips out, rocked back machine cover.]
Removed motor mounting clips and pump hoses, swinging motor and pump out of the way. Removed 3 capscrews holding transmission, pulled transmission towards me removing agitator shaft, disassembled clutch assembly - removing one cirlip then another, installed new clucth parts in same order

This is a relatively new washer and failed early. My previous whirlpool washer lasted 20 years without any repairs. 1. First inquired about the spin problem in partselect. Machine will not sping unless manualy forced then it will take off but weak. 2. Partselect suggested a clutch problem. Ordered the part that came fast. When I tried removing the shaft hub with a hammer and chisel it will not get loose so I opted ordering the special wrench to loosen the tub hub. 3. I put the machine on its back and loosened the pump retaining clips. Do not remove the hoses from the pump. Move the pump away from the motor shaft. Remove the motor electrical connector and set aside. 4. Remove the three bolts holding the gearbox-motor assemply and pull it out of the tub. 5. Put the assembly on a towelwith shaft up and remove the separator washer from the old clutch that is sitting on the gearbox. Then remove the c-retaining clip from the shaft. 6. Pry out the wire retaining clip from the clutch and pull the old clutch out of the shaft. 7. The clutch kit I ordered came with a plastic brake to clutch cam so I replaced it too, just remove the retainig clip from the brake that is at the bottom of the tub and replaced the part. 8. Installed the new clutch and the retaining clips in reverse order. Replace all parts that came with the kit. The new clutch spring was already in place. 9. Put the assembly back into the tub and re-install all the other items in the same order. It spins good now! 10. While replacing parts, methodically clean all the lint from the motor and from under the machine. The gearbox showed signs of leaking oil so its a question of cost. I left it there until it fails then I'll buy a new machine.

Unplugged the washer from the power. Turned off the hot and cold water. Took two screws off the back and raised up the upper cover. Took the power cables and water tube loose from the water level switch. Removed the switch. Put the new switch in. Removed two metal clips at the top of the washer and leaned the washer body forward. Replaced the tube with a new one. Put the washer body back in place and put the clips back in. Attached the tube to the new switch along with the power cables. Let the top cover back down and put in the two screws. Slid the new knob in place. Plugged up the washer to the power. Turned the hot and cold water back on. And commenced washing laundry.

First I removed the plastic panels on each side the control panel. Each side was secured by a phillips screw. Once the screws were removed the side panels were easily removed. I tilted the panel back to the rear of the washing machine to expose the lid switch. I first took a picture with my camera phone to ensure installing the switch correctly. I removed a small screw that secured a green ground wire. The lid switch was removed by lifting the plastic catch with a flathead (or slot) screwdriver and uplugging the switch. Reverse the steps and install the new switch. Secure and tighten the green ground wire. The lid must be lifted to properly seat the lid's guide arm into the lid switch. Replace the side panels and tighten the phillip screws. Test the wash cycle using a low water level. It took me 5 minutes to install this part. I am a attorney not a mechanic.

placed washer on side and installed new pads
and returned washer upright

Took the agitator out and gearbox off unhook wires from motor and take off water pump, replaced the parts and put back together. Pretty easy to fix. However, I still haven't got my problem fixed. Originally the washer wouldn't spin after the rinse. I put on a new coupler and it worked for a few loads, then something smelled hot and started stinkin the house up so I opened the washer lid and smoke rolled out. Turned it off. Took the moter off and checked it and it would barely turn at all. Replaced the motor with a new one. Still wouldn't spin. Put on a new clutch assembly. Still wouldn't spin. Bought a new capacitor thinking that would do it. Still don't SPIN!!! (The ring and washer I replaced was just a casualty, not any of the problem).

After removing the bolt (7/16" head), and using a pair of pliers to remove the 3-4 in deep "cup", it was immediately obvious how to assemble the new cup and pawls (ratchets).

Orienting the black "bearing" was not so obvious, but on closer inspection of the illustration, it became clear. The four "ears" of the bearing go closest to the pawls. The little tabs that are co-planar to the ears fit into the four grooves of the new cup.

And here's the trick (besides making REALLY, REALLY SURE how the pawls orient)--Soak the black bearing piece in hot water to soften it up, and let it slide over the cup better. If you don't, you risk breaking it. If you do, it slides over and "clicjs" into place, with the ears resting right against the bottom lip of the cup, capturing the pawls.

Installation back into the washer is obvious.

The thing works like a charm! It hasn't worked this well for a decade!

!. Removed agitator from inside
2.Removed outside cabinet
3 Removed pump, motor, and transmission.
4. Slid the entire drive unit out of the tub from the bottom
5. Removed the clutch assy. and installed new.
6. Reverseed the procedure to re-assemble.

3 online people recommended tilting the machine on the side and replacing the 3 suspension springs. Someone else recommended changing the tub pads. That is the wrong approach. It is actually easier to remove the case than turn the machine on the side. Once you do it once or twice it takes less than 2 minutes and it doesn't distort the suspension. You don't even have to disconnect the hoses. When I originally examined the machine lying on it's side I saw that the tub balance spring was still attached to the tub but the other end had detached. I looked for the place to reattach it. I found a place on the glide plate. Unfortunately this was the wrong place and the machine continued to bang away. When I realized that the spring had to be attached to the lower frame rather than the glide plate (one week of looking). I even wrote to the Repair guru. Once I found my mistake the repair took 5 minutes and no tools other than the phillips screwdriver to take out the 2 screws for the case. I replaced the tub balancing spring for good measure. The machine works great.

I followed instructions provided from Parts Select for removing and replacing the coupler assembly, and also instructions for changing the clutch assembly. I also took it's transmission apart (socket set and flat screwdriver required), drained the old oil, cleaned it, added new 90W gear oil. The instructions covered the swapping of parts very well. Cleaning up the oil spill took as long as changing the parts.

I thought that the lid switch was the problem why the washer would not perform the drain or spin cycle. I broke the lid switch by moving the wires around. I rigged it so my daughter could use it by screwing a screw in the switch til the new one came in. After a few days, the machine stopped working again as stated above with the motor. I purchased a new Whir-pool washer for her and later found a white wire that connects to the electric motor was burnt around the connector in that only one tiny wire was still attached. I reconnected the wire in the connector and the washer started working again.

We ordered both the motor coupling and the clutch assembly based on our troubleshooting, and because we figured both parts were inexpensive enough we might as well have them both. We initially thought it was the clutch assembly, but as we were taking the washing machine apart, we noticed that actually one of the bolts was missing completely and one had snapped in two. We then realized that the spin cycle problem was actually related to the instability of the motor because of the missing/broken bolts (they didn't even have washers!). All we had to do was replace the bolts and use a bolt extractor to get the broken bolt out, but we went ahead and replaced the clutch assembly as well for good measure. Everything ran perfectly after that! I was very skeptical to do the repair myself, but it really is easy, as long as you have someone with muscle to help out. You can also look up videos online that show you a step by step repair process for the clutch assembly, and I would highly recommend doing that so that you have a visual. It will make everything seem 100x easier.

removed old hose clamps and hose using pliers. Installed new hose which had all new clamps preinstalled on new hose.

Pop off the softener dispenser. Pull the cover/ seal out of the upper agitator. With 7/16" socket and extesion bar, remove bolt and pull upper agitator straight up and off. dump out old assembly and replace with new assembly. Set back in place and replace bolt. Repair kit comes with good instructions and new rubber O ring for bolt cover/ seal. (thanks).
The suspension spring takes more effort but not hard. with washer laying on face I used a piece of 2x4 to pick up the tub in the direction of the broken spring. Put the new spring through the wire hook loop and snake it through the slot in the frame and you can see how it locks in place. With the 2x4, push the tub toward the new spring until you can hook it through the slot on the tub frame. Done. Parts cost less than an estimate from a service call and I finished the job in 30 minutes, which includes unplugging the power cord, turning off the water and taking off the hoses so I could lay the washer down. Saved the website in my favorites for the same great prices and fast shipping next time.