Models > 3UATW4605TQ0 > Instructions

3UATW4605TQ0 Admiral Washer - Instructions

All installation instructions for 3UATW4605TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3UATW4605TQ0
511-525 of 548
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would fill with water and then stop.

  • Customer: Ashley from Breaux Bridge LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
My brother-in-law did the repair. He unscrewed the back of the top part of the machine. He located the lid switch, which is on the right from the back of the machine (left if you look at it from the front). He then unscrewed the ground wire and unhooked the old lid switch. He put the new one in place, hooked it back up, screwed the ground wire. Reconnected everything and now it works.

Washer would not begin to agitate clothes after fill.

  • Customer: Sharon from Florence MT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Lifted up the control panel, removed the broken lid switch and replaced it. Replaced missing Lid hinge mounting screws. It was great. Fixed the problem. Felt empowered to fix it ourselves for such a reasonable cost. Thanks

motor runs water in nothing else workes

  • Customer: marie from dillon SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
remove 2 screws holding top control panel down one on each side at the back / slide panel toward the front lay it over on the top of machine / unscrew ground wire /pop gray part off machine unplug wire // plug in new wire place part back into slot screw down ground wire / slide top control panel back on / replace screws on the back/ plug up and wash / it is so easy would have been faster but i had 3 kids helping to take out and put in the screws for me /

Washer would not spin or agitate

  • Customer: John from Idaho City ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1) Unplugged power to the machine. 2)Disconnected the water inlet hoses and the drain hose. 3)Placed the washer on the front of the cabinet. 4) Moved the washer to an area large enough to allow it to be laid down and worked on. 5)Removed the sound deading panel from the bottom of the washer. 6)Disconnected the electrical plugs from the motor. 7)Disconnected the two hoses to the pump. 8)Removed the two strap retaining bolts from top of the motor. 9) Removed the two motor retaining straps. 10) Removed motor and pump assembly from the transmission. 11) Removed the broken drive coupler and replaced it with the new coupler. 12)Reassembed in reverse order. Wish I had seen the brake repair vidieo before this repair was done. It shows how to remove the trasmission and motor asembley as a unit.

Screeching noise, would not drain at all.

  • Customer: Dave from Hermosa Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Got on the PartSelect website and diagnosed the problem, purchased the replacement part, received the part in 2 days....very quick. I simply watched the "how to" video for the part, which was very easy to understand, and followed the instructions and was able to take out the old part (found it to be broken), replace it with the new part and fixed the washer. It took about 40 minutes, and everything works great. Easy, cheaper and faster than calling a repairman.

failure of agitation and spin, pump works

  • Customer: Max from Redmond WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
According to the video on your site with adaptation to the exact model. More time spent in removing/replacing the cover than any other part of the job

broken coupler between motor and transmission

  • Customer: gregorio from suamico WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch the video clip

plastic part of coupling was broken

  • Customer: Judith from Concrete WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The new coupling parts are better made than the original parts. It was difficult to disassemble motor unit to get at the the old coupling, but once that was accomplished, the new coupling installed pretty easily. The machine is working fine now.

spin cycle did not engage

  • Customer: Lamar from Rochester MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
researched potential causes, found clutch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly,It was very easy to install. I also noticed oil residue on the side of the washer so after more research I found out I needed to replace the transmission also. The seal on top of the unit was worn out. I ordered a new transmission and install it and now it works like new. It's very rewarding to fix your own washer. Now all my friends are fixing their own washer and dryers. Thank You!!!

top agitator slipping

  • Customer: Frank from Baton Rouge LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
The kit comes with four dog ear cogs , the holder for them and a retainer, i could not use the holder because it would not fit my washer, only the four cogs were used.

washer work not operate

  • Customer: William from Ballwin MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug washer from the electrical receptacle. Remove one phillip screw on each side from the rear of the control panel and one hexnut with plastic strap from the rear of the control panel on each side. Pull control panel towards the front of the washer. Locate gray lid switch on the top left, rear side. Remove metal grounding screw with green wire from the metal top of the washer. Detach the gray lid switch from the electrical module and remove entire switch. At this time, open the washer machine lid carefully and gently install the new lid switch. Reattach the ground wire and metal screw to the chassis. Put control panel back in it's original location, carefully align each of the rear side phillip screws and tighten. Do the same with the two hex nuts and plastic strap. Close lid and remember to plug the washer back in to the electrical receptacle. Start the washer with your normal procedure! It should now start!!! Good luck!

Whirlpool washer pumps but drum would not spin

  • Customer: Roger from Granby CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We have a 6 year old top loading Whirlpool washer. The drum would not spin at the end of its wash cycle when it is supposed to spin dry. I followed the video exactly and it worked great. I replaced the clutch and rubber coupling. It is not difficult if go slow and methodical and you follow the excellent video My wife washes heavy rugs often and it wore out the clutch. The washer works better than it has in a long time.

washer quit agitating & spinning

  • Customer: james from beverly hills FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was really simple. I loosened pump & hose .Removed old defective parts.Installed new parts which were 10 times better enginered than original ones. Thank you for your help & quality parts. Jim Merrick Crystal River Fla.

The unit would no longer spin in rinse mode etc.

  • Customer: Peter from Grinnell IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on your website and determined I could easily do the repair. Replaced the part for less than $20.00 including shipping and received it the next day. I ordered the part @ approximately 5 PM and the projected delivery was 1.8 days. To my delight the FedEx truck arrived by 1 PM the very next day and we were up and running within 24 hours of ordering the Direct Drive Motor Coupling. I will definitely use your services again. Special thanks to your video team. I was able to watch step by step how to disassemble and reassemble the washer etc.

When the machine was filling with water about 30% of it would miss the tub and run down the back of the machine and on to the floor.

  • Customer: Kenneth from Mahopac NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After removing the front, sides and top of the machine (all one piece) the springs were relativley easy to access. I discover one of the brakets that held one of the springs had rusted and would no longer support the spring. I then replaced the bracket and springs. I Re-assyembled the machine and it work as good as new.
All Instructions for the 3UATW4605TQ0
511-525 of 548