3RATW3005TQ0 Washer - Instructions

Unplug washer. turn hot and cold water off. disconnect and mark water hoses. put a blanket on floor and lean washer on its back. use screw driver to remove metal clamps from water pump. use ratchet or nut driver to,,remove screws from metal clamps on motor.remove metal clamps with screw driver. unplug wire harness from motor. remove motor and remove old drive coupling and repelace with new part.

Remove top cap to access 1/2" bolt. Remove bolt and pull entire assembly up and off of shaft.Disassemble unit by taking long std. screwdriver to release 2 small locking tabs. Flip over and remove ratcheting upper assemble from larger lower piece.Now you will see the broken cams and be able to replace.Assemble in reverse order.

unplug electric cord. shut off then disconnect hot and cold water hoses from nozzles. place drain & water hoses over washer. place washer on floor( back/hose side down). use pliers to remove hose clamps(2) from pump. unfasten metal clamps(2) from pump. remove & replace unit. reinstall by reversing process.

Followed the video and everything went exactly as the video said! Just follow the video to a tee!

After some online research as what could be wrong with my washing machine. Several videos later, my bother found that it was the agitator, Thanks to the helpful video from Parts Select. We ordered the parts and within days the parts arrived. Installing the 'Agitator Repair Kit was really easy and took all of 15 to 20 minutes, most of which was looking over the drawing. My washer now works like a charm.. Thank you Parts Select for the speedy deliver my parts!

... exactly as shown in the video in addition to shutting water, removing hot & cold lines & waste tube. I was amazed at how fast the parts were delivered in two days regular shipping. Machine now purring a wifey happy once again! Thanks for the great service & video! I recommend PartSelect highly! WSD

Watched the video, it was so easy, if I had been a little younger it would have been a 15 min job...

Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

PartSelect has a training video for this repair. Remove the softener dispenser by popping it up with a flat screwdriver. Reach down inside the agitator and remove the bottom cap. Use a 7/16 socket on a six inch extension to remove the agitator bolt. At this point I recomment pulling the entire agitator assembly out for ease of disassembly and reassembly. Clean as necessary. Use a pair of needle nose pliers to remove the cog assembly. Place the cog assembly on a flat surface and use a flat screwdriver to remove the retainer. Note the position of the cogs and replace with the new. There are two plastic clips on the lower agitator that you can snap off to make reassemble easier. Replace the agitator in the tub. If you don't have a magnetic socket, I find it's helpful to place a small piece of paper towel across the socket to hold the agitator bolt in place as you slide it back down inside the agitator for reassembly. Tighten the bolt. Replace the bottom cap and softener dispenser.pa

I went to you tube and watched a video on how to take my machine apart.Everthing went great.I did need to buy a spanner for $23.00 @ an appliance store.

After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Unplugged the washer. Removed the 2 screws on back of control panel. Pulled the control panel forward. Flipped the control panel back. Disconnected the cable from the lid switch. Removed the ground screw with a nut driver. Opened the washer lid. Removed the lid switch. Snapped the new lid switch into place. Closed the lid. Installed the ground screw. Installed the lid switch cable. Put the control panel back in place and pushed back. Installed the 2 rear screws into the control panel. Plugged the washer in.

I unplugged washer, then, removed the control panel with two screws on back, slid unit back and up. Unscrewed ground screw and unplugged harness, lifted lid and removed switch. In order to re-install lid switch, lid has to be in the up position, otherwise it will not fit properly. Reattach harness and ground screw, then control panel. Plug and go. My wife says that the washer works better than ever. Very easy! Saves money!

It was simple. Removed one bolt slid off retainer replaced cogs. Less than 15 minutes.

Followed website instructions, worked for a couple days, appears it needs clutch or possibly transmission(red oil present)