Models > 3LE5710XKW0 > Instructions

3LE5710XKW0 Whirlpool Dryer - Instructions

All Instructions for the 3LE5710XKW0
751 - 765 of 844
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
belt broke on dryer tub
Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy
Parts Used:
Multi Rib Belt - 92-1/4"
  • Guy from Ridgeway, VA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
I had to spin drum for dryer to start, bad start winding on motor, not sure if the problem could have been fixed by replacing the motor contactor. I could not find a part # for just the contactor.
You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks
Parts Used:
Dryer Blower wheel Drive Motor with Pulley
  • Dale from Joanna, SC
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer would not run
removed 4 screws. 2 in the back and 2 at the lint screen door. Remove top lid of dryer and looked down and there was the door switch with the broken actuator spring. A diagram of the dryer with part locations is very helpful. I checked the switch with volt meter to make sure it was ok. It was ok! Replace the actuator and put every thing back together and dryer works just fine. Thanks to PartSelect I was able to buy the actuator spring buy itself and not have to buy the switch also.
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Jeffery from Cordova, AL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
belt broke
replaced belt
Parts Used:
Multi Rib Belt - 92-1/4"
  • Virgil from Angleton, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
drum was not turning
I watched your video and did the job,really no problem. I also cleaned out all the lint and dust will the drum and front were out.
Parts Used:
Idler Pulley Assembly Multi Rib Belt - 92-1/4"
  • John from West Islip, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer belt broke
Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video
Parts Used:
Multi Rib Belt - 92-1/4"
  • mark from montrose, IA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer Belt Broke
Fortunately this is an easy diagnosis and easy repair. The great PartSelect instructional videos are a HUGE HELP!!
Parts Used:
Multi Rib Belt - 92-1/4"
  • Reid from Cumming, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Broken belt
Followed the instructions that came with belt everthing went just fine.
Parts Used:
Multi Rib Belt - 92-1/4"
  • Rick from Emporium, PA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer was blowing the breaker in the house
Well it took me two tries at it. but i did it. it works great. thank you
Parts Used:
High Limit Thermostat - L290-40
  • Jerry from tacoma, WA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
dryer door switch broke
I went to internet & got the part & instructions.the shipping cost more than the part. Saved 20.00 & gas.
Parts Used:
Dryer Door Switch Actuator Spring/Lever
  • Jeff from Mamaroneck, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Dryer would only run for a few mins and then not restart. Also there was a grinding noise.
I replaced the entire motor in the dryer and the belt while I had it open and it is working great! I just watched the short video on the site to learn the tricks and did it myself.
Parts Used:
Drive Motor with Pulley
  • Andrew from Lawrenceville, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The dryer belt broke.
I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.
Parts Used:
Multi Rib Belt - 92-1/4"
  • Bill from Cooper City, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Motor hum on start-up
Trouble shot to failed motor. Ordered motor and new drive belt. The hardest part is figuring out how the dryer dis-assembles. Follow Parts Select on-line instructions. Also, several good instructional videos on You Tube! My recommendation is to order a new "blower wheel" when changing motor on a gas fired dryer. The heat combined with age bonds the blower fan to motor shaft. It had to be broken off in pieces to remove motor.
Parts Used:
Multi Rib Belt - 92-1/4" Drive Motor with Pulley
  • GREG from BLAIRSTOWN, NJ
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
Belt broke tub did not turn
took off the broken belt and the idler pully went to the internet found your website watch the video and ordered the parts got the in 3 days took 15 mins to put them on and all is good
Parts Used:
Idler Pulley Assembly Multi Rib Belt - 92-1/4"
  • Larry from Clute, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Belt popped
2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something
Parts Used:
Multi Rib Belt - 92-1/4"
  • Wade from Labadieville, LA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 3LE5710XKW0
751 - 765 of 844
Back to Top