3LCED9100WQ2 Whirlpool Dryer - Instructions

Took 5 seconds, just snapped in the slot, didn't need any tools.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.

ordered new latch kit and repaired, very easy thank you

Snapped latch into existing hole in 2 seconds. The pin that goes into latch was still intact. That's it ,real simple. The only problem I will hopefully not have in the future is the the mico-switch which is just hanging in there, the switch works but the lever that extends out from the face, that works with the door is partially broken off and the switch is no longer available on your parts list. The appliance is twenty-one years old. I am very happy with your service and I received the parts the next day, after I ordered them and I will be buying more parts in the months to come. This time it will be for my Kenmore gas stove and then a Kenmore refrigerator door hinge.

Six(6) screws were removed to separate the front and rear sections of the dryer door to get access to the rear of the catch.Pliers were used to maneuver the catch through the opening in the cabinet from the rear. The new catch was easily snapped into the catch opening from the front of the door.

Exactlyt how your video showed me. I was a bit skeptical, but it was the easiest repair ever.Thank you

I watched the video provided first to get an idea of how it should go. The dryer I have had a different kind of door, so those instructions didn't apply. You probably don't want to publish the way I ended up fixing it, but it did work eventually. Saved me over $500!! Thank you!

For 2 years, I propped a broom stick against my dryer door to keep it shut while it was running. Last Sunday night, I decided that it was about time to fix it. I found the PartSelect site, which was extremely easy to navigate, and ordered a replacement kit. It arrived in 2 days via Fed Ex and actually contained extras of each of the 2 components, in slightly different sizes. It took me about 10 minutes of eyeballing the parts to figure out how to place them and about 30 seconds to install the new latch parts. They fit perfectly. Great site, great service, I would highly recommend this site.

follow the video NOTE the felt seal was about 1.75 inches short. carefully stretch it by standing on it and pulling up on it, gradually increasing force and rotating the seal after holding a stretch for a count of 10. once it's stretched, glue it on pretty quick, it will shrink back again. this was the only surprise I encountered. my dryer runs like new now.

just the way the video showd me

I ordered the part with the manf. # BUT upon installation I found that the new part was slightly different than the old part therefore not allowing me to screw the new part to the inside of the dryer - I was able to find longer screws that would work but took me an hour to figure out what the issue was and then resolve the matter

replaced the lent filter

diognostic suggested thermal fuse or thermistor. Thermistor tested low resistance (<2K olms). Replaced thermistor and dryer heat returned.

Our dryer got so loud after running for a few minutes that you couldn't even have a conversation in the same room. After researching for possible causes, I decided to go with new drum wheels. I purchased the Dryer Repair Kit to save a little money and it gave me a new belt and tension wheel as well (since I was going to have it apart anyways). After taking everything apart and vacuuming out all the lint from inside, I noticed that the blower wheel was broken. No idea how that happens but something must have gotten in there and broke 2-3 fins and cracked the rear side. I replaced the parts that came with the kit and proceeded to put it all back together. Started it up and it was worse than before. Quickly ordered the new blower wheel and that fixed the problem. Back to a "quiet" dryer. I probably didn't need the Kit after all, but the drum wheels were a little worn and I had it apart anyway.

Took the old one out and replaced with new filter.