Models
>
3KSM6583TWH0
3KSM6583TWH0 Whirlpool Mixer - Overview
Sections of the 3KSM6583TWH0
[Viewing 3 of 3]Keep searches simple, eg. "belt" or "pump".
Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This part is a retaining ring, sometimes called a retaining clip, that holds the drum support roller onto the shaft of a dryer. It is made entirely of metal and measures less than an inch in diameter....
$7.88
In Stock
Torx Screw
PartSelect #: PS11741257
Manufacturer #: WP3368921
7-18 x 3/4" - sold individually.
$6.54
In Stock
Retaining Ring
PartSelect #: PS11746917
Manufacturer #: WP9703680
Used on Stand Mixers.
$8.99
In Stock
Retaining Pin
PartSelect #: PS11746974
Manufacturer #: WP9707223
This part works in conjunction with the worm and bevel gear.
$9.03
In Stock
Bowl Arm Lift
PartSelect #: PS11746961
Manufacturer #: WP9706885
This is a replacement bowl arm lift for your stand mixer. It raises and lowers the mixing arm in the bowl. It is made of white plastic and is sold individually. This part can also be known as the bowl...
$10.08
In Stock
Wire Whip
PartSelect #: PS11746914
Manufacturer #: WP9703491
This part is the replacement wire whip for your stand mixer. It is made of metal and is approximately 7 inches from top to bottom, and 5 inches from side to side. The wire whip is an attachment which ...
$34.34
In Stock
Coated Flat Beater
PartSelect #: PS11757062
Manufacturer #: WPW10672616
The Coated Flat Beater is an OEM accessory specifically designed for 5 and 6 Quart KitchenAid stand mixers. This flat beater is responsible for thoroughly incorporating ingredients when mixing or blending recipes.
$26.06
In Stock
Bowl Retaining Pin
PartSelect #: PS11740496
Manufacturer #: WP240185
Used for Kitchenaid Stand Mixers.
$7.29
In Stock
Questions And Answers for 3KSM6583TWH0
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 3KSM6583TWH0
[Viewing 3 of 3]Noisy
Fixed by
these parts
these parts
Show All
Gas igniter glows, but will not light
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The mixer would not raise the bowl
I removed the motor assembly from the mixer. This left the stand assembly. The raising lift arm had to be removed by unscrewing the set screw, and then the lift arm was removed. I replaced the plastic arm bowl lift by sliding it over the lift arm, and then I had to remove the spring with a clip washer with the pliers, and replaced the spr
... Read more
ing back on to the new part. Total time about ten minutes for the actual fix, and about 45 minutes remove and reinstall the 12 screws that held the motor in place. It was well worth my efforts. The mixer arm works perfectly now.
Read less
Parts Used:
-
Stephen from Charlotte, NC
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
11 of 16 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
all four feet on mixer damaged
I first ahd to remove the original feet by removing screws that held them in place. The new feet that I purchased were different then the original. They were a push in type and not held in by screws. I had to modify the base by drilling the foot holder to accept the new style feet. Once this was done, the feet were installed and looke
... Read more
d good.
Read less
Parts Used:
-
ROBERT from ENDWELL, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed to replace rubber foot on mixer
The insertion part of the foot was tapered to fit in the hole in the mixer. Simple pressure was not the answer. So I used a small key, placed it on the bottom of the foot, after applying a little vegetable oil on the foot, and tapped it into place. Worked well.Joe
Parts Used:
-
Joseph from SAINT LOUIS, MO
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
2 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!