3ED25RQXXW00 Whirlpool Refrigerator - Instructions

First, turn of the water supply. Then remove the snap on grill from the bottom front of the refrigerator. Disconnect the black hose from the white hose and drain the hoses into a suitable recepticle. Then remove the 1/4" screw that holds the nozzle in place. Cut the hose off just behind the nozzle bracket and tape the end of the new hose to the now exposed end of the existing hose. From the bottom of the door you can now gently pull out the old hose while pulling in the new one. Re-attach the new hose to the existing white hose and replace the 1/4' screw to the new nozzle bracket. I reccoment using 1" wide tape and only going around the tubes once. Too much tape and you won't be able to feed it through the small hole at the bottom of the door. Have someone feed the hose from the top as you gently pull from the bottom.

Being a jet mechanic I had to familiarize myself with refrigerators, then after 2 or 4 hours of online studying, opened the door pulled the temp knobs of, removed the panel by gently prying the top of the panel out,then up and out with it. I found tapping on the thermostat shaft or wiring connection started the compressor, verifying my belief it was the thermostat. Don't mess with wiring if you don't know exactly what you are doing and unit is plugged in, you will electrocute yourself!!! I received the thermostat, UNPLUGGED THE UNIT from the house wall outlet, took one screw out of the upper inner wall at the very top to remove cover, one screw at the back top to remove the other cover (at the control vent) for access to remove sensor, then removed 4 screws , 2 front, 2 underneath to drop the housing for defrost timer, etc., and then took 2 screws from thermostat, unplugged wiring from thermostat (3 wires, be sure to put them back on the same place in the new thermostat). Remove old thermostat, slide plastic cover off sensor and slide back onto new thermostat sensor. Be careful not to kink the line or bend it to sharp you will damage it, (use gentle curves when bending it,) and re assemble everything in reverse order. This took about me 15 or 20 minutes start to finish. Plug into wall and watch thermometer to verify success.

changed the starter connected to the compressor

1. shutoff water
2. removed 3 screws holding old ice maker. A small nut or screw driver is needed to get into a somewhat tight area
3. detached electrical connector
4. cut indicated area for water inlet to lie in
4. attached new electrical connector (no splicing needed)
5. attached new ice maker with 3 screws
6. put on water

Removed the top two screws and one on the bottom which attach the ice maker to the side of the freezer. I unclipped the wire bundle from the side of the ice maker and unplugged the connector, totally removing the unit . The maker came with several different wiring setups, but I just used the existing. The contol arm on the new unit basically snaps into place and the above process is reversed to install the new unit. My old ice maker had an accelerator which blows cold air to the bottom of the tray to speed up ice production. This component was undamaged and by taking off the new units outer end cap and borrowing the clips from the old unit, this component can be installed on the new ice maker.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

Unplugged refrigerator. Used nut driver to remove small bolt retaining wire cover on right side of ice maker. Removed wire cover, used flat head screw driver to depress side-rail clips. Ice maker slid out, unplugged. Timer module cover pops off easily. Three screws removed the timer module. Installation was reverse of removal. Had ice in less than an hour, bin was full by next morning. If you have a screw driver and know what it's for, this job should come easily.

I noticed the coating inside the ice maker, the lining on the surface that the water contacts when making ice, was chipping off. I replaced the ice maker with a new unit and now there's no more bits of stuff in my ice. The other problem I had was the ice bin, it had picked up a weird smell over the years and I wanted to replace it. The new bin seems flimsier, but works fine. It didn't have the top attachment hole for the ice auger mechanism drilled out for some reason, it had a little "bump" in the plastic where it should be, but was never drilled out. Easy enough, I drilled the hole out and attached that top screw without any issue.

part arrived within 24 hours.
1. remove plastic front of freezer door water and ice dispenser by looking at bottom edge of plastic for two slots within which to place a stiff scraper blade. very difficult to pop loose and very fragile plastic so take care not to break it. it just pops off two spots on the bottom side and hangs from the top no screws or anything.
2. remove the two screws holding the water dispenser spout in place. oh yeah don't forget to turn the water off.
3. this is a long plastic water tube that runs from the dispenser thru a plastic tube channel set in the solid foam core of the door thru the bottom hinge and connects to the water inlet junction.
a. this replacement must be pulled from the dispenser area thru the door and out the bottom but it will not fit without cutting off the end of the spout. the hole in the hinge that it passes thru at the bottom of the door is to tight to allow anything other than the thickness of the tubing.
b. pull the spout end of the tubing upward after disconnecting at the bottom in front behind the air grill. if it moves freely you are in luck - if it does not move freely then it is taped in place on the back of the dispenser area and now that whole assembly has to be unscrewed from the front of the freezer door in order to remove the tape so that the tubing can be pulled thru.
4. once the tubing pulls easily as short distance in either direction it is time to attach the new tubing to the old tubing and pull it out the bottom of the door. i tried to use tape but it pulled off when i got to the door hinge on the bottom and it would not fit thru the hinge.
a. on my model even one layer of tape would not fit thru the hinge. so i put some bricks under the freezer door to hold it up and removed the bottom hinge off of the tubing that was disconnected only a short distance away.
5. use tape or place a screw with the head removed into both the old tubing and the new tubing so it can be pulled from the bottom moving the new tubing into place.
mine broke off in the middle of this process and i had to remove the freezer door. take it completely apart to expose the conduit the tubing slides thru, then run an electrical fish tape thru the conduit and drag the new tubing thru, not a fun process but doable - just takes a bunch of extra time.
6. once the tubing was out the bottom i could then simply thread it thru the hinge easily and reassemble everything.

I unplugged the fridge. Loosened the 2 top screws on the ice maker and removed the lower screw. I disconnected the wiring harness and removed the Ice maker. I removed the plastic timer cover in front. I then loosened the screws on the face of the ice maker and removed the broken ice stripper and replaced it with a new one. Re-tightened the screws on the face, installed the timer cover, plugged in the wiring harness, re-attached the ice maker. Plugged the fridge back in and walla, it was making ice in 30 minutes!

removed screws that held the ice maker in place, then removed the cover (popped off) The drive element was easy to remove, three screws and it was out. I put in the new part and reinstalled the icemaker with the three screws that hold it in place. I never call Sears for any repair. They use contract help and I have heard horror stories about those guys!

Unplugged refrigerator. Removed lower back access panels and panel running up the back of refrigerator. Removed and disconnected old fan. Removed old fan motor from mounting bracket. Removed fan blade from old fan motor and placed on new fan motor. Connected new fan motor to power supply. Tested. Reinstalled.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Took off door to ice maker. Unscrewed 1 nut. Slid out unit. Unplugged electrical connector. Unsrewed 3 nuts from bottom of old unit & attached mounting bracket to new unit. Reconnected electric connector. Slid back in. Put screw back in. Put icemaker door back on. Turned icemaker on. Ice in 20 minutes!