Models > 3ED25DQXBN00

3ED25DQXBN00 Whirlpool Refrigerator - Overview

Get Parts and Repair Help for 3ED25DQXBN00

If you know the refrigerator repair part you need, you can browse the list of all parts on the 3ED25DQXBN00, or you can search by name or part description. You can also find your part by where it is located on the 3ED25DQXBN00 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for 3ED25DQXBN00 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.83

Door Cam

$23.19

Ice Bin Auger Drum

This white ice bin auger drum comes with a washer.

$56.69

Thermostat Assembly

The thermostat will sense the temperature increase in the evaporator during the defrost cycle and will cycle the defrost heater off after the ice or frost is melted.

$10.86

Door Closing Cam Kit

This door closing cam kit is intended for use with the bottom of refrigerator and freezer door hinges. The cam helps with the closing of the doors and to keep them slightly in position when opened.

$3.76

Shelf Support Stud

Sold individually.

$10.59

Micro Switch

$27.33

Bi-Metal Defrost Thermostat

If ice is building up in your freezer or if your freezer is getting too warm on the defrost cycle you may need to replace the bi-metal thermostat.

$3.76

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

$2.70

Screw

This screw is sold individually.

$3.46

Shelf Support Stud

This stud is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

inconsistent compressor and condensor fan operation

  • Customer: Steve earney from Brooks GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 114 of 117 people found this instruction helpful
Compressor start relay would cycle several times before compressor would come on. Replaced start relay and defrost timer assy. Operated more consistently however not completely reliable. Ice would begin to melt. Noticed that if you would cycle the temperature control the compressor would start again and operate for several hours then not cycle again. Jum... read more

Plastic bits dispensed from Ice Dispenser in Door

  • Customer: john from seaford VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 100 of 110 people found this instruction helpful
Removed Ice bin from Fridge

Removed all bolts on bin with nut driver...about six

Removed housing...be careful with spring on crusher/cube control rod

Removed C clamp on end of auger with small slotted screw driver and needle nose pliers.

Removed plastic nut on end of auger shaft

Removed Ice crusher jaws ... read more

The door would not close properly. The CAM had broken.

  • Customer: Thomas from San Clemente CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 84 of 85 people found this instruction helpful
The repair was very simple.

1. Remove the food from the door shelves.

2.Remove the door by first removing the three screws holding the hinge at the top of the refrigerator.

3. Lift door off of the bottom hinge.

4.Replace bottom CAM on bottom hinge (one screw)

5. Replace top CAM and shim on door (one scre... read more