Models > 3ECKMF86

3ECKMF86 Whirlpool Ice Maker - Overview

Get Parts and Repair Help for 3ECKMF86

If you know the ice maker repair part you need, you can browse the list of all parts on the 3ECKMF86, or you can search by name or part description. You can also find your part by where it is located on the 3ECKMF86 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your ice maker. We’ve also included any installation videos we have for 3ECKMF86 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the 3ECKMF86 [Viewing 2 of 2]

$72.18

Icemaker Control Assembly

This part is used to help tell the icemaker what to do - it turns the timing cams and the ejector blades. Motor is not sold separately.

$3.76

Icemaker Water Fill Tube Kit

This kit comes with a fill tube and a compression nut.

$15.79

Water Fill Cup and Bearing

$3.56

Water Tube Kit

This tubing is 1/4'' in diameter and comes with 2 inserts. This tubing may be longer than the original, and may have to be cut.

$24.48

Thermostat with Clips

This part is also known as the cycling thermostat and this bi-metal device controls the activation of the icemaker ejection cycle.

$3.96

Compression Nut

$2.70

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$2.70

SCREW

$4.46

Plastic Tubing Inserts - 4 Included

These inserts are used with 1/4 inch plastic tubing.

$26.48

Shut Off Arm

When the shut off arm is high enough the ice maker will shut off and no more ice will be made until the level of the ice in the bin drops. Also the ice maker can be turned off by lifting the arm all the way to the top until in a locked position.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No ice

  • Customer: Daniel from Suwanee GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 306 of 365 people found this instruction helpful
removed flap door in front of icemaker...removed 3 screws with bolt heads...removed one additional screw with bolt head and ice unit slid out. I removed motor unit (pops out no screws). Replaced and had ice within 3 hours. read more

Ice Maker stopped working

  • Customer: Robert from Port Washington NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 79 of 89 people found this instruction helpful
With socket wrench un-screwed the 3 screws and pulled out the ice maker assembly.

Pulled off white plastic end-cap and noticed the plastic gear disk had snapped off (sub part # R0167202)

However, it is all-one-part of the motor assembly unit # w10190935 (part # PS2341896) which must be ordered as a complete part.

Unscrewed t... read more

Broken elbow on icemaker water fill tube.

  • Customer: Charles from Orland Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 66 of 73 people found this instruction helpful
Removed 2 screws holding water fill tube to rear of refrigerator and pulled out, matched old part with new to make sure of proper match. Guide new fill tube thru hole, making sure it is aligned with slot in ice cube tray on inside of freezer. Install new plastic line from water pump outlet to water fill tube, check for leaks, job done. read more