3CGP2951BN0 Whirlpool Dryer - Instructions

I won't tell you how we did it, but I'll tell you the right way. Unplug. Remove the exhaust tubing attached to back of dryer. Pry the top up from the front and lean it against the wall. Un plug the wires attached to the front panel (remember where they go) Remove screws at top sides of front panel. "lift up" and remove. Close top. Lay machine on its back. We used a couple of 2x4's to lay it on so as not to crush the vest collar. Clean it out, including lint filter. The new belt wraps around the drum, you will see the channel about midway on drum. Feel behind the motor on the lower right side. There is a shaft with a channel for the belt. Immediately next to that is another pulley type arm with another channel for the belt. This arm moves stiffly and puts tension on the belt when installed correctly. Look at the diagram included with the new belt which shows the path of the belt. Wrap the belt, ridges against the drum and then around the motor shaft. At this point you have to physically pull the last arm out to allow the belt to wrap around the channel provided. If the belt is not twisted , the job is done. Turn the drum with your hands to make sure it is turning properly. Replace the front panel, plug in the electricals, replace the screws making sure the drum is properly centered. Stand up the dryer. Plug in and turn on dryer to make sure everything is right. Replace the exhaust tubing and set into place. Sounds like a lot of steps but I have described the whole process for you beginners. The rest of you will know already. Good Luck . Oh by the way we are 69 and 71. If we can do it, so can you

Unplug the dryer, remove hot air duct. Remove metal dryer back to access thermostat using a nut driver. Unscrew one screw holding on thermostat, detach 4 wires, and replace with new unit, attaching 4 wires to new unit. Then reverse process to button up the dryer. Great how-to video on your site helped a lot!

Pulled the old one out, took the duck tape off (haha) and snapped, pushed the new one on. Piece of cake. I then noticed that this is a movable door ,and ther was the same part on the other side, oh well now I still have a spair.

I watched the video several times to make sure I got it right. The first thing that was very helpful was how to disassemble the top cover and front panel using a putty knife to disengage the detents. With the cover off I could acccess the belt and idler pulley. Replacing the belt was fairly easy as long as you note the way it threads through the idler pulley and drive pulley. I thought the video was excellent. It took me right to the problem and the fix. As a bonus the price for the belt was much lower from Parts Supply then from Sears. I've recommended this site to several others.

First I purchased the heating element, still no heat. Then I purchased the thermal fuse,still no heat. I have been pleased with the prompt shipment of the parts and the parts arrived safe. Thank you for service and time, not sure what to do now.I will recommend PartSelect to friends.

Unplug unit / removed back cover / went down , locating both parts to be replaced / simple one screw removal from each part / thermal fuse , one wire @ a time , reinstalled . / Cycling thermostat , 4 wires. Did one wire @ a time , reinstalled. / Putted back cover back on , plugged dryier back up, turned it on to run. To check for heat / yes, ran good as new. Later that day some more running , with damp clothes in it. Did it's job , dry.

Took the back off of the dryer, looked on "parts select" found what I thought might be the problem. Got the parts the next day. Put on new thermal fuse, then put on cycling thermostat. Wasn't sure which it needed, so put both on. Put the back of the dryer on hooked the gas up, hooked up to electric, & turned the dryer on. Back in business, everything works, dryer works as if nothing was wrong. Thanks to "parts select" saved me a repair bill.

I watched your video on how to replace the fuse.Wow it was a lot easier than I thought.I would highly reccomend anyone to watch the video before even trying to do any repairs.The dryer is working like a new one.By doing it myself saved me a lot of money.Thank you

Removed two screws at the top, removed two screws for the front panel, removed the broken belt, installed the new belt, followed the directions that were in the new belt package, and replaced all the panels and tested. It worked.

Removed the broken actuator and replaced with the new one. The time to replace the dryer door switch actuator took about 5 minutes.By the way, I purchased the dryer in 1965 and it works as if it was brand new. Thank you Kenmore for a lifetime dryer.

Just as in the video. Sounds like new. Had to feel it to make sure it was running.

Man o man...please listen up. Would not start..replaced the thermal fuse was the first step I took according to web sight...started right up... Then it took 2 cycles to dry clothes..I went down the recommendations from the highest. % to the lowest %..replaced. over 80$ in parts..cleaned out all vents..from lint ext...still would not work..then come to find out my kids jammed a small toy in the exhaust flap on the outside of the house..the flap stayed closed when the dryer was running..there was no place for hot air to go but back in the dryer..and it seemed to run fine..but the sensors were cutting off the heat early...lesson learned..do not buy any parts until u clean all lint parts..vents..and make sure there are no obstructions with air flow..other wise this is the best place to buy parts..period..

two screws on filter housing and then lift dryer to up like the hood of a car the two screws on actuator, be careful not to drop actuator, if you do use a magnet to retrieve, two screws back in then wire clip top of dryer down and two screws back into filter housing and your ready to dry clothes, not recommended but if you have to dry clothes while waiting for part a clamp on the switch will allow you to use dryer, but be extremely careful because dryer will not turn off when door is opened

I went to partselect.com, input my model number and problem, I clicked on the right solution and watched a short video on how to repair the problem. Ordered the parts which arrived the next day. It took me ten minutes to replace the two parts I had ordered and the problem was solved. I probably saved a couple hundred dollars doing this repair myself..

Replaced Thermal Fuse