Models > 3875ERS > Instructions

3875ERS Jenn-Air Range - Instructions

All installation instructions for 3875ERS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3875ERS
46-51 of 51
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Light burned out in upper oven

  • Customer: Shirley from Las Vegas NV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed in light bulb and glass protector

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

The Grill Element stopped working...

  • Customer: Anthony from Spring Hill FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Went on the computer typed in the part number and their web site came up.. So I called and ordered the part I needed. Was sent very fast. Was grilling by the weekend...will do business with them again.. I'm glad I found them .Thanks...

Filter worn out, exhasut fan kept going off

  • Customer: John from Cayce SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Old filter allowed too much air flow causing exhaust fan to go off....installed new filter in exhaust chamber...release clip on old filter and install new filter (at an angle) in the exhaust box....clamp down clip on edge of filter and job is complete

Heat Errosion

  • Customer: Fred from Temple Terrace FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Wife installed them, they just snap into place on the Rock Grate.

right-side door hinge was broken (completely)

  • Customer: Michael from Lumberton NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Make sure to insert a solid screw/nail/metal rod approx. 2" long, into the hole in the original hinge (doing so will preclude the hinge from "slamming closed" against the oven opening frame; plus, it holds the hinges in an offset position which makes it easier to just slide the door upward and off the hinges.) NOTE: the replacement hinge will come with a retaining pin already in place that "holds" the hinge door shaft at about a 45% angle to the spring assembly. DO NOT REMOVE THE PIN until AFTER the door is remounted on the hinge. As mentioned, just grasp the door sides and lift the door upward to clear the hinges shafts. With the retaining screw/nail/rod still inserted, the hinges are easily managed. with the door removed, two screws each hinge will be exposed. they will are easily removed. after they are removed, one will be able to manipulate to remove the hinges assemblies from the oven body (no need to remove any other oven parts). After the old hinges are removed, just install the replacement hinges into the mounting cavities and secure the hinge mounting screws (two each hinge). Slide the door on to the two hinge shafts and remove the two retaining pins. Attempt to close the door. if the door does not fit properly (too high usually), then open the door enough to reinsert the retaining pins. Remove the door and adjust the two metal screws at the very tip of the hinge door shaft to get the door to fit properly (usually you will have to turn the screw in-I had to). Reinstall the door, remove the pins, and check the fitting, making sure the door fits properly. You are done! I needed a pair of vise grips to remove the broken piece of the door shaft that had broken off in the door mounting cavity.
All Instructions for the 3875ERS
46-51 of 51