Models > 37511KBSERWW > Instructions

37511KBSERWW General Electric Refrigerator - Instructions

All installation instructions for 37511KBSERWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 37511KBSERWW
76-90 of 143
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

sticky switch

  • Customer: ANTHONY from NEW EGYPT NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
easy pry out, disconnect wiring, connect on new switch and press in switch.

Refridgerator was warm, Evaporator Fan was stuck

  • Customer: Stephen from Philadelphia PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Followed the video by Parts select. Very accurate to remove and replace. The only trouble I ran into was getting the clip back onto the fan blade shaft! Have to improvise and use a wirenut to spread it and it went right onto the shaft. Now working perfectly! Thanks for the video and the fast part service shipping...

Broken Vegetable Pan Cover

  • Customer: Juaneese from Madison TN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I replaced the Vegetable Pan Cover myself and it looks and fits great. The hardest job was unloading so that the previous cover could be taken out. I was proud of myself for being able to do this job myself without any help. Ordering and receiving the part was so easy that I will always use Parts Select. Thanks again. Juaneese

fridge stoped cooling

  • Customer: stephen from vernon AL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
unplug fridge! removed ice maker. removed the back panel in frezer. I uncliped thermostat; cut wires on thermostat and installed new thermostat.

Compressor not coming on

  • Customer: Kevin from Morris IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.

fan motor froze up

  • Customer: Norm from Westcliffe CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
followed the video provided on internet by Parts Select. Video is very well done. Thanks

Replacement gasket

  • Customer: Dewey from Laurel MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I took it right out of the framed box to keep the gasket in shape and snapped it back on the gasket mount on the freezer door it took 5 minutes or less perfect fit

Frame broke

  • Customer: Denise from Clementon NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I was so surprised when I went on line put in the model number the item came up so quickly, price was cheap I order the same day less than 2 days it arrived. Love the site will use for many things moving forward, service was quick and easy it took me less than 5 minutes total to find site and order product. I would recommend site to anyone that needs pieces for your appliances.

Loud noise from the freezer area during the defrost cycle

  • Customer: Glenn from Lincoln MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed all the freezer inside panels to inspect the motor before I ordered the part. It looked like a relatively easy job to change it. I also watched the really nice video on the website that re-inforced my confidence in doing the job. The part came in a few days. I disassembled the freezer interior exactly as the video showed.(Warning: be careful with the styrofoam piece if the fridge is not fully defrosted. The ice build-up could cause it to break when trying to pull it out!)The only problem I had was getting the little collar on and off the motor fan shaft, and getting the fan off the shaft. I had to pull really hard for it to come loose and then I had to push really hard to get it back on the new motor shaft. I didn't know if could have used any kind of lubricant or not, so I didn't. After that the re-assembly inside the freezer went well, being careful to put everything back in the correct order and position. Started the fridge back up and it has been running very quietly ever since. But, most important, my wife was impressed with my work and is very pleased with the result!

motor makin load hum

  • Customer: paul from renfrew PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Part came in a couple of days, very fast delivery. Read how other people installed. Only drawback was the youtube video was not available. Thanks again!

Sides of old shelf cracked

  • Customer: Daniel from Carlsbad CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Pulled out old shelf and put in new one. However the new shelf is too narrow and will break at some point just like the old one. Apparently no way to fix this issue.

Missing a Shelf Guard on freezer door

  • Customer: Patricia from Hampton VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Simply "popped" the guard into place...a very basic fix. Thank you so much for your customer service (the lady who waited on me was awesome, shipping was super fast, and it was the "Correct" part)...singularly, one of the best transactions I have had in a very long time...kudos to you. Definitely will use your site again.

not cooling

  • Customer: cyril from holden LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
refrigerator was not cooling. with new fan the refrigerator is working so well I had to turn it down to "1" to get the temerature right.

Broken freezer door shelves

  • Customer: Richard from Stockton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just popped the new ones in.

Evaporator fan motor making loud noise

  • Customer: John from Bedford Hills NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched video repair by Hotpoint , Everything went like clockwork and was a total success. Repair took exactly 25 minutes.
All Instructions for the 37511KBSERWW
76-90 of 143