36568 (P1108503W) Litton Refrigerator - Instructions

I performed the replacement just as the video instructed. Very simple repair.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

I followed the instructions from your video. I did this replacement all by myself. I am a 64 year old woman and have never done anything like this before. It could not have been any easier.

Thought we'd try the Water Valve before replacing the ice maker. Ordered new valve online on Saturday, it arrived on Tuesday. I installed it twice in less than 30 mins. Had a little leak the 1st time, so I uninstalled it, trimmed up the water line with a box cutter and reinstalled without issue. No leak this time. Easy Peasy. My husband said "You're good, you." :)

Replaced icemaker and used wire harnnes and plastic cover off old one. Real easy!!

The ice maker change out was easy. The problem was the part came with a different filler cup but the one needed was supplied. Changing to the other cup required taking the ice maker apart and installing the other filler cup. Go to the parts list and find the filler cup. Use instructions found there to change to other cup and then install your ice maker.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

removed old icemaker and transfer some of the parts to the new icemaker. The only problem was that I had to disasemable the new icemaker to replace the fill tray with the older style (which was included). Once that was done, installation was pretty easy.

I removed the old ice maker as described by the DIY video and had no problem except, I had to remove the ice tray from the motor section so the end cap could be changed. This only required removal of two Phillips screws on the case of the motor assembly, that are used to to secure the tray. Once the tray was off, the ice ejector could be removed and the end cap was free to change. Everything was re-installed in reverse order and unit was mounted. An FYI to anyone with slow ice making, will need to check their freezer temperature. Make sure it's set to get as cold as 5-10 degrees Fahrenheit. After installing new maker, it was not making ice fast enough, only to find my freezer temperature needed to be changed as well. Everything is working as it should now.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

The ice maker was easily replaced, however I still had no ice. I ended up using an on-line repair service which determined that the problem was the water inlet valve. Replacing it was beyond my expertise so I hired an appliance repairman.

just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time

After reading the articles previous owners wrote, I tackled the repair. There were no big problems until I had to change out the water line on the icemaker tray--that part was for a different frig--so it had to be changed out with the Amana water line part that was enclosed. I couldn't get that part removed, so I had to have my husband change it out. He then finished the installation. Everything went smoothly, just my pride wanted me to finish it all by myself.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.