Models
>
3644803591
3644803591 Kenmore Range - Overview
Sections of the 3644803591
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Bake Element
PartSelect #: PS249249
Manufacturer #: WB44K5013
This bake element is used in ranges and located at the bottom of the oven. The bake element supplies heat for baking. If your symptoms include: your oven is not heating evenly, not starting, or the he...
$71.47
In Stock
Light Bulb - 40W
PartSelect #: PS217532
Manufacturer #: 40A15
This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
$11.02
In Stock
Broil Element - 240V
PartSelect #: PS249244
Manufacturer #: WB44K5009
This OEM-sourced broil element with push-on terminals is located on the roof of your oven cavity, providing heat from above to cook and heat your food. It requires a 240-volt power supply to function ...
$81.33
In Stock
Broiler Pan - Large
PartSelect #: PS1517612
Manufacturer #: WB48X10056
This large broiler pan is found in the bottom of your oven and is used to catch drippings from broiling foods. This part includes the grate and bottom pan and is made of porcelain. The grate measures ...
$30.07
In Stock
Door Gasket
PartSelect #: PS244569
Manufacturer #: WB32K5038
This gasket seals the oven door.
$159.97
Special Order
Limit Switch
PartSelect #: PS236592
Manufacturer #: WB24K5033
This part acts like a safety thermostat on the appliance. Once it reaches a certain temperature it will shut off the heat source (element) to make sure the temperature doesn't go any higher.
$59.68
In Stock
Questions And Answers for 3644803591
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the 3644803591
[Viewing 4 of 4]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bake element shorted out, sparking like a sparkler
first, made sure circuit breaker was off
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element
this was ... Read more all done by my 15 yr old son under my supervision.
second, used nut driver to remove 2 screws on old element, pulled it from the back of the oven
third, removed 2 wires from old element (spade connectors)
fourth, connected new element and pushed back into oven.
fifth, reinstalled 2 screws securing new element
this was ... Read more all done by my 15 yr old son under my supervision.
Read less
Parts Used:
-
Carl from Wynnewood, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
89 of 97 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The broiler element caught fire and burned out while I was broiling a steak.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches, but I had not turned off the power.
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pu ... Read more ll the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
So, I shorted out one of the wires. Then I turned off the power but was afraid to go any farther.
An appliance repairman was at my house that day fixing my dryer seal. He was able to pu ... Read more ll the wires through the insulation successfully and install the broiler element. He did not charge me any extra for this little extra job. But I learned my lesson. Cut the power before you begin! He told me that I could have wound up with a much bigger repair if the short had been in the wire that is connected to the control panel of the oven. I was very lucky!
Read less
Parts Used:
-
Dianne from Rockville, MD
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
67 of 75 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Convection Fan motor was (way) noisy
Fan motor has to be removed from the rear. Since this is a (double) wall oven, the hardest part was sliding the oven out of the wall.
First, doors are removed, eight screws that hold the oven in place (along the side of the doorways) are removed. The rear panel inside the oven must be removed to expose the fan. Four screws hol ... Read more d that in place.
Next, slide out the oven. The fan is covered by a tin shroud which is easily removed with a nut driver. The blade of the fan (inside the oven) is held on by a reverse threaded nut which must be removed. The fan motor is mounted with three screws and has two wires plugged into it. Piece of cake.
Reverse the procedure and you're done.
The best part was that I had originally called a service guy, who was going to 'defer me to GE for the repair' because the oven had to come out of the wall!! I think I'm going into the repair business!
First, doors are removed, eight screws that hold the oven in place (along the side of the doorways) are removed. The rear panel inside the oven must be removed to expose the fan. Four screws hol ... Read more d that in place.
Next, slide out the oven. The fan is covered by a tin shroud which is easily removed with a nut driver. The blade of the fan (inside the oven) is held on by a reverse threaded nut which must be removed. The fan motor is mounted with three screws and has two wires plugged into it. Piece of cake.
Reverse the procedure and you're done.
The best part was that I had originally called a service guy, who was going to 'defer me to GE for the repair' because the oven had to come out of the wall!! I think I'm going into the repair business!
Read less
Parts Used:
-
daniel from sayville, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench (Adjustable)
54 of 56 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!