Models > 36291112004 > Instructions

36291112004 Kenmore Range - Instructions

All installation instructions for 36291112004 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 36291112004
181-195 of 195
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

stained drip bowls

  • Customer: Sunny from Salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unplugged burners replaced drip bowls plugged in burners

Bake Element burnt out

  • Customer: Greg from Chicopee MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
watched the video on part select - took less time then they said.

GE Electric Range rear left burner quit coming on

  • Customer: Richard from Richmond TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Connector to burner is out.

  • Customer: Jonathan from Lynn MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Remove old wire and replace new wire into place.

Needed to replace drip bowls

  • Customer: Gloria from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.

Bake element not working

  • Customer: Rodney from Chambersburg PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 days. excellent service. Thanks

Corroded connectors and melted block on an electric stove.

  • Customer: Jacqueline A from West palm beach FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
The original GE blocks/wires were color coded to specific burners. The new ones are not color coded since they are sold individually and work with any burner, but they were identical to the originals in every other way. Just remove old blocks one at a time and connect the replacement so that the burner is connected to the proper control. Since the stove age was unknown, I replaced all four blocks to eliminate a repeat of the problem later. The screws holding the blocks and the wiring cover on the stove back require the same small socket wrench; not enough room in some places for an adjustable wrench. It took no more than 20 minutes to replace all four, test the burners, and close up the back wiring panel. The instructional video on the website eliminated my hesitation to tackle this repair. The parts arrived the next day, with no special shipping service requested. WOW. PartSelect will be the first place I go to find what I need for the next fix-it. I'm almost looking forward to something else breaking. LOL. Thanks, PS.

one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.

  • Customer: brendan from lebanon NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

piece out of the oven gasket. Old and brittle.

  • Customer: Alice from Valatie NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Remover the old gasket and replaced it with the new. The small prongs I removed with pliers. Need to make sure that the new gasket isn't twisted when you put it on.

The terminal block for a front stove top burner failed

  • Customer: Tom from Kensington MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
There was an excellent video demonstrating a very good method for replacing the terminal block at Parts Select.. I ran into a problem with the kit. The wires were too short. Instead of replacing the entire wire I needed to clip off part of the old wiring and solder the kit wires to them. I also needed to insulate the connections with electrical tape to prevent them from shorting out.

oven was overheating, temp would not drop, oven light would not go off

  • Customer: Schen from Port Townsend WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
First and foremost this website was very easy to locate the part number that we needed. Unplugged range from the wall. Removed the upper metal plate off of the back. Removed the ovens' control knob in the front, then removed the 2 screws that released the thermostat. Opened oven door and released the metal thermostat probe. Cut the other end of that wire at the thermostat switch in the rear of the range. Taped that wire to the new metal probe. pulled the old probe out the front of the oven pulling the new probe in place. Switched 1 wire at a time from the old thermostat to the new one in the back of the range. Works great. No more burnt muffins !

Two Stove Elements weren't working

  • Customer: Scott from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Found PartsSelect on the internet. Saw the video for replacing the Surface Burner Terminal Blocks with their kit. Turned a $400 oven replacement into a $25 quick repair, thanks to PartsSelect.

Bakelite block in the terminal block broke in two.

  • Customer: Jack from Mayview MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I can add nothing to the video you furnished on your website. I am generally all thumbs with home repairs - especially anything electrical - but, your video led me right through it. A good experience. We'll do business again.Thanks.

TOTAL BURN OUT OF ORIGINAL BROILER ELEMENT

  • Customer: richard from Palm Coast FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Remove lower drawer and contents. Unplug unit. Tilt Range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach Broiler element connections from wire clips(2). Insert new element, Attach 2 new connections to clips first. Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then Broiler.

I needed an oven with three racks, mine came with two.

  • Customer: BETTY from CYPRESS TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
just slipped it in
All Instructions for the 36291112004
181-195 of 195