Models > 36275205891 > Instructions

36275205891 Kenmore Range - Instructions

All installation instructions for 36275205891 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 36275205891
31-45 of 269
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

inner glass on door broken

  • Customer: Christy from Mountain Center CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 6 of 8 people found this instruction helpful
my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.

Oven would not ignite

  • Customer: Jeffery Jankowski from Bronx NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 5 people found this instruction helpful
1. Moved oven from the wall.
2. Unplugged the stove from the electrical outlet.
3. Removed over racks and bottom panel.
4. Located wires leading from the igniter in the back of the stove.
5. Disconnected the wires from the ignitor.
6. Used socket set to remove screws from ignitor.
7. Cut connector plug from new ignitor.
8. Stripped about a half inch of insulation from wires of new ignitor to be able to connect it to stove.
9. Carefully handled new ignitor and screwed it into place.
10. Attached wires of new ignitor using new caps.
11. Put bottom panel and racks into place.
12. Plugged oven into electrical outlet - Oven ignited and made a good dinner.

Spark was present in only two of four burners

  • Customer: Paul from Maurertown VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 6 of 8 people found this instruction helpful
Repair was quite easy. Remove four screws and lay back sheet metal panel. Transfer wires from one module to the other and then put new module in place. replaced the sheetmetal panel. Spark now presen at all burners. One small thing worth mentioning. Each burner has a gas distrubution cap and that cap has a small hole to the spark cavity. One of these was pluged with grease and that kept the burner from lighting until this hole was cleared.

burner tubes both had pin holes in them and the ignighter didnt work

  • Customer: David from easton MD
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench set, Wrench(Adjustable)
  • 6 of 9 people found this instruction helpful
This was a real easy job and a success,of course any repair i do on a gas appliance and when finished It doesnt blow up i consider a success.
Thank you,David Williams

end caps on range were cracked

  • Customer: James from Federal Way WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 4 of 4 people found this instruction helpful
I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it meant buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.

stove top burner ignition spark progressively got weaker and then stopped on all but one burner.

  • Customer: George from Villa Park IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 5 of 7 people found this instruction helpful
I located the igniter module by following the wires to the top/rear of the stove. Removed two sheet metal guards and marked and numbered each electrical wire before removing them. Reasembled in reverse order. Wife thinks I'm a genius!

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Only one burner sparking on range.

  • Customer: Ronald from Freehold NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 6 of 11 people found this instruction helpful
Removed spark module only two small nuts. Inside was six wires on terminal. Removed one by one and connected right to the new module. Easy job 10 minutes and finished.

Wife broke gas lines when trying to clean under hood

  • Customer: Scott from Corinth MS
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Wrench set
  • 4 of 5 people found this instruction helpful
Removed old line with wrench and attached new line to gas valve first. Then lowered hood to the stop and attached gas line to burners.........very easy and works fine now.

Needed extra oven space

  • Customer: noreen from flushing NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 8 people found this instruction helpful
Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

Gas oven igniter for a GE Profile XL44

  • Customer: Carolyn from Oakdale AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 6 of 11 people found this instruction helpful
Once we knew which part was needed, we went on to your site and orded the part. It was delivered the next day! Partselect.com is bookmarked on every computer in our household, including mobiles. It's great to know there is such a fantastic resource for do-it-youselfers. It took 5 minutes to remove the old igniter and plug in the new. A screwdriver is the only tool required.

Oven rack missing when I purchased the house

  • Customer: Patricia from Houston TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 12 people found this instruction helpful
I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

Oven would not ignite

  • Customer: Todd from Falcon CO
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
First I removed the broiler from the bottom of the oven, then pulled the oven way from the wall to unplug it. I then removed the two screws that hold the igniter element in place. Ironically, the plug GE manufactures is reversed so i had to strip the plug and go end and reverse the wires to attach them to the oven. I used ceramic wire attachments as plastic would surely have melted. Replaced the screws, replaced the broilers, plugged it in, replaced against the wall and it fired up.

Oven wouldn't heat

  • Customer: Erin from San Diego CA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
I let my brother do the actual installation but it only look about 15 min. I did look at the website of the appliance manufacturer first and then came to this website. The cost of the part I needed was almost half as much as the other site. When I saw that someone with the same oven model number and had the same problem and was able to fix it, I decided to order here. It came quickly and my oven now works.

Oven would not heat

  • Customer: Andrew from Alexandria VA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 3 of 4 people found this instruction helpful
This would've been an easy repair, but I ran into some complications.

First I removed the thumb screws holding the bottom oven pan, took the pan out, and also took the bottom panel off the front of the oven.

This gives you access to the burner assembly. I disconnected the wire to the ignitor. I then removed one screw at the front, and two in the back of the burner assembly with a 1/4 socket wrench.

The burner assembly came out. I tested the ignitor for continutiy with a multimeter to ensure this was the faulty part. There was not continuity, so I knew the ignitor needed to be replaced.

This was when I tried to unscrew the ignitor, and both screws stripped their threads on the burner mounting plate. Complication #1. Seems with age, that mounting plate tightened up on the screws.

I cut the screw heads off with a dremel and cutting wheel to get them out. I'm glad I did this before ordering the new part because I needed to order the replacement screws too.

The burner mounting plate for the ignitor needed to be re-tapped to get the new screws in with a 10-32 tap and power drill.

Once the mounting plate was properly rethreaded, I attached the new ignitor, and reattached the burner assembly to the oven.

When trying to connect the wires, the plastic connectors wouldn't click together. They matched up fine, but wouldn't go all the way in. Complication #2. While the plastic connectors were properly mated, the inside pins were both female. The old ignitor had male pins on it, the new one had female pins. So I removed the burner assembly again, cut off the new ignitor connector and spliced in the old ignitor connector with the included porcelain wire nuts.

I put the oven back together again, fired it up, and it worked great.
All Instructions for the 36275205891
31-45 of 269