Models > 36275205891 > Instructions

36275205891 Kenmore Range - Instructions

All installation instructions for 36275205891 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 36275205891
256-270 of 285
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

oven ignater

  • Customer: Sharol from Dallas Center IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I did not do it my husband did and it went very well.

Oven would not turn off even though knob was turned off.

  • Customer: Jeff from Geneseo NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unplugged stove. Removed the top rear panel to see where the thermostat cable fed into the oven. Left the current cable in place and fed new cable along side the old one. Pulled out the old cable once new one was installed. Attached wires to new thermostat and installed. Turned oven on to test. Everything went great.

oven would not lite

  • Customer: Russell from Reidsville NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
took off old initer and then had take off that little cover to get to the end of the wire so i could unplug it .thorugh it was kind of britale it fell apart abit .plug the other one in and put it on &turn the oven on and it came right on!it went well.thank you

Replace oven gasket

  • Customer: Jenny from Muskego WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
I used the pliers to remove the old pins, and popped then new pins in place...super simple!

Thermostat knob broke off

  • Customer: Rudy from Waterloo IA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Cut off the power. unscrewed the cover. fed the new thermostat inside the over and rescrewed. Feeding the line was the most time consuming finding the hole to insert it in the back of the oven.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

OVEN WOULD NOT TURN OFF

  • Customer: Thomas from Burlington OK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened up the top of the stove using a screwdriver. Lifted it up about 3 inches and legs popped out on each corner and held it in that position. Traced the wire to the back and down to the oven. Pulled new thermostat along that route. When I got to the back it was a little tricky moving the thicker end around and down into the hole without removing anything from the back- but I did manage to do it. I then unhooked old thermostat from 2 clips, inserted new one and then went to the front and unsrewed the 2 small screws behind the oven control knob. Magnetic bit on screwdriver is a must! Pulled it back and removed wires one at atime and put onto new unit, then screwed it back in place and replaced knob. Plugged it in and turned it on. It came on ,stayed lit. Turned it off and it stayed lit- surprised me......25 seconds or so and it went out.....job done!!

knob was too large for new switich.

  • Customer: larry from mulliken MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
ground off rear of knob 1/4" . Put on new knob and works fine. No longer have detents but can still read knob.

Oven took longer and longer to warm up, then wouldn't ignite at all.

  • Customer: Richard from Patterson LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Unpluged power. 1. Removed all internals from the broiler. 2. Removed (3) protective heat shields. 3. Pulled glowbar plug through the access hole behind the gas piping. 4. Unplugged the glowbar. 4. Removed two glowbar holding screws and remove the glowbar. 5. Waited two and one half days to recieve the new part. 6. Reversed the process. NOTE: It really was not difficult at all, and the new part was original equipment so except for the delay in identifying, ordering, and receiving the part the whole process was very quick.

it would glow, but it wouldn,t light

  • Customer: Robert from New Hope MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took out the bottom broiler drawer and reached to the back of the oven. i loosened the screws,unplugged it and replaced the igniter and plugged it in and put it all together and it works great now.

My stove would not light at all.

  • Customer: Jajuan from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
It was easy I unplugged the stove but I left the gas alone. I used a flat head screw driver to take the oven sheet off. Then I unscrewed the oven lighter and the bracket holding it. Then I disconnected it and put the new one on. The hard part was letting the wd-40 dissolve for the rusty screws

No Spark

  • Customer: Milo from Plainfield IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The instructions were to unscrew the top, and lift. It was very difficult to do, just to see that the part to change was not there. It was in the back of the range. Oh Well.

Replaced damaged oven rack

  • Customer: Vicki from Irvine CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Gas oven would not ignite

  • Customer: Russell from Maple Shade NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Using your information that was posted i order the part that was most likely the problem. The video was spot on for the replace part.

Fails to maintain set temp.

  • Customer: Ronald from Arkport NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
watch the video. Do the repair. What could be easier. Bake some cookies just for a test.. I did it twice just to be sure. Thank you partselect. Rite part, rite price, fast shipping, arrived next day...............
All Instructions for the 36275205891
256-270 of 285