36041 Refrigerator - Instructions

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

While investigating a water leak I discovered the condenser fan seized. I removed the fan to prevent a fire and ordered the part. The hardest part was identifying the correct fan. That took longer than the installation.
I cut the wires and spliced in the new motor. It rotated correctly and I replaced the crill.
Done
Total time of ice maker water leak repair and fan replacement about 1 hour.

First step, call the repair man. He listened, and then said to get a new refrigerator, since this one is 28 years old and the repairs could amount to a significant part of the price to buy new. Even if he fixed this, it could develop other problems, yada. So we went out to buy and discovered nothing suitable that would fit in that slot of our kitchen! We'd need new counter top and cabinets to fix this problem! So we went to the Internet and searched to find the likely source of the problem and the parts schematic at PartsSelect.com. Yah! We ordered the part, and then found we had no idea how to install it. Sooo, back to the Internet, and eventually got some good clues - it goes in the kick space under the front, and just plugs in, once you can get to it by removing the bracket that holds it. Working underneath a refrigerator is not complicated but it's awkward. The form of the new timer was not exactly the same, but it does function correctly. We have no experience whatsoever with appliance repair, so pretty amazed at our success. This old Amana looks very good inside and out and is now working perfectly again. If it lasts a few more years, we will be thrilled to have spent $15 to save $500. We can always buy new later on.

Confirmed that the solenoid controlled water valve (Part # PS358631) between the water source and the back of ice maker was defective. I did this by removing the valve and plastic hose from the back of the refrigerator and pointed the end that went into the icemaker towards the sink. I applied 110 volts to the valve and noted that no water was getting through. Replacing the valve was a snap.

Unplug
Remove entire back panel (both chipboard and metal fan grill)
Unscrew both fan mount plate screws - fan won't be able to come out because it is still plugged in
When looking at back of fridge, locate a small plastic box to the immediate left of the condenser. It's a circuit block. Release the metal spring clip holding the plastic cover in place, and trace the fan wire connections back to the fan. Make a note of which wire is connected to which terminal (1 of the fan wires has white lettering and 1 is just black)
Unplug both fan wire connects from circuit block to release the fan power cable.
Remove the fan mounting plate
Release fan blade clip by pressing fan against motor and unscrewing and remove fan blades
Unscrew motor from brackets - note alignment of motor on brackets
Mount new motor on brackets. Leave plug wire disconnected (replacement motor has a harnessed plug wire)
Connect new plug wire to the circuit block keeping wires connected to the proper terminals
Snake new plug wire behind condenser like the old wire was and run through cable bracket to the back right of the condenser
Plug wire harness into motor and re-mount fan mount plate
Reattach fan blade and secure using blade mount kit
Replace back panels

I was not sure what was causing the problem, I thought at first it was low water pressure causing the hollow ice cubes. After some trial and error testing I figured a likely cause could be the water valve in the ice maker itself. I replaced that part rather easily using the existing fasteners in about 15 or 20 minutes. The ice maker has been working flawlessly since the repair.

simply removed old motor and replaced new. I'm over 82 and it was hard to get down and up to floor level!! One thing was a little puzeling -that was to insert the right screws which had a nitch in the end of the threds to keep it from loosening- I thought I was spoiling the threds cause I had to use a little pressure to start the screws and thought I had the wrong screws--they had sent several sets of them for different name brands- but II got it and everything seems to be allright - Could you tell me if I could purchase a replacement compressor and some refrigerent -the new kind. thank you, George Erlandson Only if my comp. goes out!!!

R & R Icemaker Assembly. Took out 3 screws and unpluged Icemaker & replaced with new part. very easy and the service from PartSelect was fantastic.
Very Satisfied,
Ron Martin

Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

Icecubes came out half-way, and refrooze. I figured out, that the melter does not work (HEATER in the icemaker) Voltage measured 105V no load. Studied the Internet, and folloved an advice: shorted the back wire and the blackwire with white stripes.these go to relay contacts. It seems, that the relay contacts are no good on Infrared receiver boaed. I turn off manually the icemaker, when needed

Replaced the part--
Door snaps loudly everytime it's opened or closed.
Correct replacement part and lubed with vaseline,

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) Then I put the new valve in, put the cover back on the refridgerator and was done. total time 15 minutes. My wife says I'm the man.

It was so easy!

Thanks for the rush to my home on the part.

I just unscrewed the plate that locks in the light switch (screwdriver) and unplugged the old faulty part and plugged in the new switch, screwed the cover back on and I was done!

Easy!

And I am not Mr. Fix-it!

Had to disassemble ice maker to install part. . .

As the prior stories mentioned, this was a fairly easy fix to a nagging problem. Heck, we almost bought a new refer over this, cuz the door would keep popping open.

Needed a screwdriver, and a 5/16" nut driver (mounted in elec. drill). Have two people for this one! Emptying the door would help out tons too. ('course, I didn't do that!)

With the door closed, remove the plastic cover on top by removing 1 phyllips screw. Then, using drill mounted 5/16" nut driver, remove 3 hinge screws. Remove hing by lifting up. Now, carefully open and remove the door. Here is where the 2nd person comes in. There are 2-3 1/4" screws (Must use a 1/4' NUT DRIVER, SOCKET OR MAGNETIC BIT HOLDER) on the bottom of the door to remove the broken plastic cam. Also, you must remove the bad cam from the bottom hinge using I believe the 1/4" nut driver.

Finally , one person lift the door while the other kneels on the floor to help giude the door back onto the bottom hing pin. Close the door, ensuring that the top of the doors are even, and secure the 3 top hinge screws. UR done!

Greg