Models > 3521XRW > Instructions

3521XRW Magic Chef Range - Instructions

All installation instructions for 3521XRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3521XRW
241-255 of 315
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bake element burned out

  • Customer: Donald from Largo MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove racks, remove 2 screws, pull element out, disconnect connectors, reinstall new element.

heating element went out

  • Customer: kim from rockford OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
part was sent quickly and it was easy to remove and replace. also watched video

Baking element blow out

  • Customer: Evelyn from Henniker NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Turn off the oven and let it cool. Remove the door by pulling it upward. Remove the racks and pull out the drawer under the oven and set aside. You should be able to reach the electrical wall outlet. Unplug the unit. Unscrew the metal tabs holding the element to the rear of the oven. Pull the element out about 2 inches so you can reach the clips attached to the wires. This is why you must unplug the stove. Wiggle the clips until you can pull them off the element. Don't let them slip back into the insulation. Bend them upward if necessary. Replace with the new element. Put on the clips. Ease back into the insulation. Replace screws. Plug back in and you are good to go.

Burner element stopped working

  • Customer: Robert from Lodi CA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair itself is really quite easy. Cut the wires, strip the ends and attach the new receptacle with wire nuts. The hard part was getting to it. My cooktop is about 30 years old, so I had to wade through piles of nasty built up grease. Some of the sheet metal screws were unworkable, so I had to cut them off with a Dremel tool. Not a pretty picture, but that's how repair work is on old stuff.

Porcelan Electric Burner Plug broke

  • Customer: John J from Coatesville PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The video on your website showed me how to take out 1 screw, cut the existing wires and strip the ends. The kit came with 2 porcelan wire nuts to re-connect the wires and it was done. Less than 10 minutes. It saved me $100.00 to get it repaired.I bought 2 in case I need another one in the future.They only cost $11.00 each. Awesome website.

Drip bowls were all rusted.

  • Customer: Robin from Seneca SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed old rusted drip bowls and put in the new ones. Very easy to do and needed no tools. It made my 25 plus Jenn Air look new again!

burners would not come on without moving them around

  • Customer: Ronald E. from Marissa IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took old screw out of stove top that held them in and cut the two wires off close to the burner stripped the wires and used the screw caps to put each line together it doesn't matter which line goes where and screwed it back on with the old screw and tried the two burners and they both worked job done ps it took longer for me to type this but i am slow at typing

Front 8" stove burner got excessively hot at any setting

  • Customer: John from Manchester MI
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Performed repairs just as you directed. Everything went in in without a hitch. All the parts fit well and seem to be working fine. Wife still complains. Maybe I need a new burner coil.

Rubber seal was broken

  • Customer: Jennifer from Lynn MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Broke the same day I installed it

The bake heating element burnt as I was baking some bread in x-mas just like a welding machine

  • Customer: Mario from Lutz FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I went to your web site and luckily I saw all the comments from people that had similar problems . It was awesome then I ordered the part and you had instructions on DIY . Great web site I will recommend it to anyone

old drip bowl was worn out

  • Customer: Richard from Germantown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
new drip bowl fit perfectly and was a snap to install.

replaced oven lightbulb

  • Customer: peggy ann from forest city NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
very easy

I ORDER 2 SWITCHES FOR 8" HEATING ELEMENT

  • Customer: KAHN T from SAN MARINO CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TURN OFF POWER 220V, OPENED COOK TOP, REMOVE OLD 8" SWITCH AND REPLACE WITH ONE OF THE NEW SWITCH PS2089438. HOWEVER, I HAVE ANOTHER COOK TOP, IT IS A 6" HEATING ELEMENT. CAN I USE THE SAME SWITCH FOR 8" AND USE ON A 6" HEATING ELEMENT? SINCE I ORDER 2 NEW PS2089438 SWITCHES. THANK YOU FOR YOUR ANWSER. KAHN LEE

Oven lower element burned out

  • Customer: rick from west palm beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair was simple and made even easier by the part select web site. I'm very well versed on the web but have never ordered from a site quite like this. Having customers comment on their experiences in the actual use of their purchases is a super idea. I followed the instructions posted by others and found the replacement of the element easy. Thanks for all the input of other do-it-yourself experts.

Oven light Switch

  • Customer: William from APACHE JUNCTION AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.
All Instructions for the 3521XRW
241-255 of 315