Models > 3521XRW > Instructions

3521XRW Magic Chef Range - Instructions

All installation instructions for 3521XRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3521XRW
226-240 of 302
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Both storage drawer wheels fell of the drawer

  • Customer: Michael from Blacksburg VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I ordered two wheel and shaft kits, assuming they would be complete with all the parts, they weren't. Each kit consisted of (1) shoulder bolt and (1) nylon wheel. However, there were no nuts or lockwashers in the kits. Luckily, I have a large collection of miscelleneous hardware and was able to match thread sizes and complete the repair. TOO bad the parts sheet is incorrect. I can foresee problems for folks not as equipped as I was.

I needed to replace my burner pans.

  • Customer: Robert from Wilton CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The Drip Pans are a cinch to replace with no tools necessary. The best part is that the Web Site is extremely easy to use, and the parts arrived two days after being ordered.

one pole of the socket corroded to nothing

  • Customer: martien from williamstown MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Starting by me making a substitute prong to keep the stove working while the part this coming by mail. was a piece of cake.

Leveling legs were broken during the summer

  • Customer: Jayne from Willimantic CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
The range in my classroom had the leveling legs broke off by the summer staff. I ordered two new leveling legs and the night custodian replaced them in about 45 minutes and them leveled the stove. Parts were just as stated and easy to order.

Receptacle was no longer making good contact.

  • Customer: Fred from Edwardsville IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
This worked out GREAT. We were about to purchase a new range when I found the needed parts were available. The stores we had contacted had told us our range was too old to have parts available. I had no problem with installing the receptacle at all. The pans went in easly as excepted. My wife is happy with her NEW arrangement. She does not need to learn how to operate a new range. Thanks for your help. The instructions sent were clear and easy to follow.

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

oven temp would not heat above 100º

  • Customer: Joseph from Malvern OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed old element - replaced with new element - perfect fit Thank you Part Select fast delivery easy installation by using part select online instructions.

Oven not heating

  • Customer: Dennis from Brewster NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First I turned off power to the range. I then removed the oven door for easier access to the rear of the oven. I removed baking pans and 2 oven racks. With a nut driver, I unscrewed the holding screws attached to the rear of oven heating element. Then pull the element forward exposing wire push-on connectors and slide connectors off the element. Reverse the entire procedure, set oven temperature to about 350 degrees to check element function and voila! bake some cookies.

drip pan were burnt out

  • Customer: Delroy from Miramar FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
simply remove the burner take out the drip pan and bowl individually. Install the new one and replace the burner. no tool was used.

the oven had stop heating at any temp above 200

  • Customer: Harry from Kaplan LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the 1st thing to remember is to turn off the breaker for the stove then open the oven door and remove the racks and the heating element was there on the bottom undo the screw on each side where the element goes into the back wall of the oven and pull gently out and take your plyers and remove the wire hooked on each end becareful so that the wire does not fall back into the hole place your new element into the oven and plug the wire on the new element and slide it back into the holes and put back the screws and when done you can put the power breaker back on and try it this took less than 15 min.

Front burner would not heat properly.

  • Customer: Michael from Milton FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Ordered a front burner but it was not the right size. Ordered a switch after local dealer said I had a bad switch. Ordered a switch from Parts Select and received it the next day. Works good now.

burnt out bake element

  • Customer: thomas from santa fe NM
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I viewed the video you sent [ which will bring me back to you for all my appliance parts ] and could have done the repair in less than 15 min. but one of the leads on my oven was too short so I had to disconnect it from the terminal to connect it to the new element and feed it back through the oven wall and reconnect it to the terminal. I will recommend you with out hesitation. Thanks, Tom P.

on Indicator light on all time

  • Customer: Euclides from Orlando FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Disconnect the range from wall outlet. remove 2 screws in the back of the cabinet,remove switch plug. connect back range to outlet to check if it is the switch. make sure the light isn't on. then I order the switch online at PartSelect.com and it arrived in 2 days. When I installed the piece, the problem had been solved. I hope this information will be helpful for others.

Replaced Oven Heating Element

  • Customer: Stuart from Perry UT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The oven heating element blew out on Thanksgiving... it went in style sending pieces of molten metal around the oven. After a thorough cleaning and removal of debris I obtained a replacement element. Replacement is easy. There are two screws that loosen the element. The connectors are a push-fit. The oven works great now.

Bake element burned through and broke

  • Customer: Gregory from Daly City CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the element by removing two screws. I discarded the old element and installed the new one using two screws - just as shown in the video. I ordered the part and received it in just a few days. The price was good. Very happy.
All Instructions for the 3521XRW
226-240 of 302