Models > 3510PRW > Instructions

3510PRW Magic Chef Range - Instructions

All installation instructions for 3510PRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 3510PRW
271-285 of 298
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls tarnished.

  • Customer: Jennifer from Albion NE
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove heating element coils. & old drip pans. Install the new drip pans and reinsert the heating elements and insure all elements were level. For aesthetic reasons I replaced all the drip pans - 2 x 8" & 2 x 6".

Baking element burned out during self cleaning cycle

  • Customer: Roberto from Arvada CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
KILL POWER FIRST. I should have read other entries on here prior to starting. I would have learned that one leg of the element is always hot. Fortunately it arced against the oven, and all I had to do was replace the terminal. Could have been much worse. Unplug range or shut off circuit breaker prior to doing any electrical work. Verify 0 voltage before starting if you shut off the breaker.

Heating Element Caught Fire

  • Customer: Michael from Lawrenceville GA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
During normal use, the heating element on my electric range burst into flames one day. Judging from the internet, this is actually fairly common! It's an electrical fire, so it's important to shut the oven off at once, and not a bad idea to cut the circuit breaker immediately. Then put the fire out and unplug. Remove what's left of the old element by unscrewing 2 mounting screws where it enters the oven rear wall. Taking door off of oven made it easier to lean in there. Then pull the crimp connections apart to get the wires off of each end. There are videos on youtube and partselect.com showing how. One thing they don't mention is that the wires may want to disappear back into the hole in the oven wall once they're loose. So hang onto them. I put a piece of duct tape around each one to keep it from slipping back into those small holes. When the new element arrived, I just reconnected the two crimp connectors and re-mounted the two screws. Of course, make sure range is unplugged while you're in there. Those two wires have 220V on them. I'm also never again going to leave my range on, either in baking or cleaning mode, when I'm not home. That fire was scary!

elament burn out

  • Customer: Alton from Wetumka OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
just removed two screws installed the unit replaced the two screws

oven would not come up to temperature

  • Customer: Pauline D from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Turned off circuit breaker to oven. Removed old unit by undoing screws and remove from clamp.Put to unit in by placing it to clamps and adjusting so it was level and screwed it back in. Voila! But now I think I need a sensor..

Burnt out bake element

  • Customer: Janet from Hillsboro ND
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
My husband did it and was very easy. Has been done before too. Very fast service from you also. Will order again if we need to.

part of original burner not working

  • Customer: SUSAN K from SEDALIA MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
slide new burner in slot and turned on stove. Worked perfectly.

Door seal was pulled out by grandson.

  • Customer: Michael P from Hickory Hills IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 0 of 0 people found this instruction helpful
finished removing door seal, used pliers to remove old securing studs. positioned new seal and pushed securing studs into existing holes and was done.

The drip pans needed replacing.

  • Customer: Alison from Carnation WA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Put in the new drip pan -- which are really nice shiny ones.

my wife decided to clean the oven and while holding up element broke the end off. leaving the wire hidden inside.

  • Customer: robert from iva SC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Assuming you dont have the same problem as I this will be a very simple repair.Unscrew 2 phillips screws holding the element in place, then gently remove connector wire from each side .careful as it may be brittle and detach itself. Leaving the power wire inside and unreachable from the front of oven. once you have old elemement out slide connectors onto yynew element replace screws and your done

Replacing a faulty bake element.

  • Customer: keegan from Winona MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. First make sure power is disconnected from appliance. Either by unplugging unit from the receptacle or by turning off the breaker supplying power. 2. Next remove the shelves from oven, to give yourself enough room to work. 3. Next remove the two Phillips screws holding the two brackets, where the bake element goes into the back wall of the oven. 4. Carefully pull the bake element out from the wall of the oven. Just enough to expose the two wire terminals. 5. Using the pliers carefully wiggle the wire clips off of the spade terminals on the bake element. 6. Remove the old bake element. 7. Connect the new bake element to wires. Make sure that terminals have solid connections before inserting the element into the back wall of the oven. 8. Reinstall the bracket retaining screws. 9. Turn power back on and check that oven and the new element is functioning. 10. Let oven heat for about 15 minutes before placing any food in the oven, as there will be a slight odor from the new element. It will diminish quickly. 11. You're done.

Bake Element burnt in half

  • Customer: Kelly from Register GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I simply unscrewed and removed the old bake element. Then popped in the new bake element according to the directions in the Youtube video that was attached to my order confirmation email.

Dirty drip bowls

  • Customer: Paul from Carnegie PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Just remove old bowls from range top and put new ones. That is all ... just super simple! :)

Dirty drip bowl

  • Customer: Paul from Carnegie PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Remove old drip bowl from the range and put a new one back.

Maytag Electric range oven bake element burned out.

  • Customer: Charles F from Melrose Park IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Before starting, shut off power to the range with the circuit breaker or fuse, or unplug the service cord. The bake element is the lower element. Remove the wire oven shelves for easy access. Using a Philips#2 screwdriver, remove the two screws holding the old element to the rear of the oven. Gently pull the element straight out until you can see the connecting wires come through the holes. These wires are connected to the element with spade clips. Remove the clips by pulling them straight off the old element taking care that they do not fall back into the holes. Put the new element in place, connect the wires to the terminals, and slide the assembly into the holes. Replace the two screws, restore the power and you are done.
All Instructions for the 3510PRW
271-285 of 298