3468XVA Magic Chef Range - Instructions

removed the top plates, the burner heads and their ignition wires. removed the four screws from the range top that hold the gas orifices to the top.Lifted the top off of the stove. used a 1/2 inch open end wrench to remove orifice tube assemblies. put the new tube assemblies in place, wrenched them down, secure but not overly secure. replaced other materials in the same way the they were removed. it took about thirty minutes. had some difficulty replacing the stove top.the stove is an older model and some of the pieces moved when the top was removed.

Repair was super easy, Remove Screws. (the hardest part was trying to remove the edging of the door without cracking it, or breaking the tabs used to secure it) Once I got the edges off, I slid the front of the door off, removed the screws and braces holding the outer glass. Picked out the broken pieces, cleaned all the glass and inside the door and put it all back together. If I didn't clean everything, it would've taken half the time.

I replaced the Dual Oven Safety Valve and that didn't fix it. Turns out that even if the igniter glows it still can be the problem. Since the igniter is in the circuit of the Dual Oven Safety Valve, each igniter is responsible for their half of the Dual Oven Safety Valve. Apparently as the igniter ages the ohms of the igniter go up reducing the voltage below the 3.3V to 3.6V necessary to open the valve (bi-metal strip wrapped with cal rod wire inside of Dual Oven Safety Valve). Once the ohms go up and the voltage goes down no gas is released from that half of the Dual Oven Safety Valve. So it will appear that the Dual Oven Safety Valve is bad but that is not the case. It will be the Igniter corresponding to the burner that is not lighting.

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

I removed the sensor from the oven using a philip screw driver. The sensor was removed by removing the two screws holding it in place in the upper left hand corner of the oven. I had to disconnect the sensor on the back of stove. Then I pulled the old sensor through the hole inside the oven. Then I installed the new sensor by putting the wire of the sensor through the hole where the old sensor was removed. Then I hooked up the wire in the back of the stove. Then took the screw driver and replaced the two screws holding the sensor in place. It was very easy to do and the oven is doing fine now.

Cut off the electricity at the junction box. Removed two screws from the sensor at the back of the oven. Then pulled the sensor with the wire out of the installation hole in the back of the oven. Disconnected the quick connect plug from the sensor and reconnected the new part. Reversed the process and screwed the two screens back into the oven wall. Turned the electricity back on and started up the oven. (Everything ran well for about three days when the oven again signaled "F-5" indicating the oven was again not functioning properly. Restarted the oven and is currently running properly. My spouse does a lot of baking with this oven for cookies, roasts, etc. Next time it fails I will be forced to call a repairman as I believe there is something wrong other then the heat sensor.

the repair was not difficult ,take time cause back panel has to be removed to gain access to unplug the temp sensor ,it appear to work but the digital clock still flash not all the timebut it should not flash , not sure that i have fixed it

The hardest part was removing the burners themselves, I used an oil filter wrench to twist them off. After that it went pretty quick. I also used a toothpick to clean out the holes on the burner, and now the igniters work on all the burners.

This is a no brainer. I am only doing this because you asked. Pull out the stove, tilt it back, remove broken leg, install new leg.

took oven door off easy just lift up took bottom tray to oven out took bottom draw of stove out removed tin panel cover 2 screws to unplug igniter took 2 screws out of igniter and pulled unpluged wire through insulation. installed new igniter 2 new screws put wire through insulation and pluged it in. The only thing to check is matching the plug ends correctly before pushing them together.

Basic instructions provided were accurate. Most difficult part was bending down and reaching across the oven door. A general information note would have been helpful. The circuit that feeds the igniter and the gas valve is a series circuit. So, even though the igniter was glowing cherry red, the igniter was still the cause of the gas not flowing, The voltage drop across the igniter was larger then normal causing the voltage to the gas valve to go down and to be insufficient to allow the gas to flow.

After watching your do-it yerself video, I turned off the gas and unpluged ac power cord, I removed the stove door and then removed the bottom tray inside the stove unscrewed tray plate pulled buner out of its housing. I then unscrewed the two screws to the old ignitor and unpluged it. Pluged in the new one screwed it to the burner bracket, put everything back togher then tuned on the stove. IT WORKS!!

Removed the oven burner changed the igniter reinstalled the burner still didn't operate,gave up purchased a new range. I liked dealing with your sales department very friendly.

This is one of the easiest home repairs I have ever done. I shut off the gas and unplugged the oven. I removed the door and shelves. I then removed the two screws that secured the igniter and pulled the connector through the hole in the back of the the oven. No need to splice any wires as the replacement igniter came with the correct connector. It was then just a matter of reversing the process. Very simple and quick fix.

Replaced the oven igniter and oven works perfectly 30 seconds to light