Models > 32 1272 23 07 > Instructions

32-1272-23-07 Frigidaire Range - Instructions

All installation instructions for 32-1272-23-07 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 32-1272-23-07
1-9 of 9
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.

  • Customer: Jonathan from Arkport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove.

Two top burners would not light, defective switch

  • Customer: Donald from Middle Village NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Warning- we found a lot of bare wires in this stove, check your wires before replacing the bad switches. I lifted the top, disconnected the power, pulled off the knobs, unscrewed the switch for the back light, removed seven screws to finally get the front panel off. Once you have the front panel off, changing the swich takes less than a minute. The switches just slide off the gas valve stems. Instructions show how to line up the new D-shaped switch mechanism to match the D-shaped shaft. Gently pull the two wires off the old switch and slide onto the new switch. Then put the panel back.

tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE

  • Customer: Jose from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.

Grates were old and rusted and scratching the bottom of my pots

  • Customer: Sue Z from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

Switch plate cracked.

  • Customer: Len from Corry PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 3 of 5 people found this instruction helpful
This hard to find GE part number was easy to find at PartSelect.com. The GE dealer said the part was permanently out of stock. Lift lid and remove a few screws and pull off two wires and replace switch plate and reconnect everything. Good to go.

Gas burner went bad

  • Customer: Kenneth from Hickman NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had the old burner already out, so all I had to do was insert tab into slot and then fasten with screw. Tried the burner and it worked, I just had to adjust the amount of air it received. Very satisfied with product and quick delivery.

Gas will not start

  • Customer: Paresh from La Palma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the range. Opened the range by removing the burners. Removed exiting spark module then installed new one. Just make sure the four plugs are correct.

oven would not ignite

  • Customer: Diane from Southbridge MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the gas control valve was removed ,then the igniter. The new part was plugged in and the valve was applied. It started right away. I want to thank the sales man, he sold us just what we wanted, not the one we thought we needed which was 240.00. My repairs cost $42. and a meal for my son and a friend. Would reuse this service again if needed.

there were no problems

  • Customer: Richard from Oak Lawn IL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took off the front panel where the burner nobs are was very easy
All Instructions for the 32-1272-23-07
1-9 of 9