Models > 32-1012-00-03 > Instructions

32-1012-00-03 Frigidaire Range - Instructions

All installation instructions for 32-1012-00-03 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 32-1012-00-03
1-9 of 9
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My burners would not light. There wasn't the tell tale "click, click, click" of the spark module.

  • Customer: Jonathan from Arkport NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 16 people found this instruction helpful
First I had to slide the stove out of its cubby and then I removed the two screws holding on the shield. I next removed the wires going to the spark module. I removed the top screw and loosened the bottom one. Installed the new spark module in reverse order. Less than 15 minutes for whole repair. Still have problems with spark module not working if oven is on, but I think it is because there is no air circulation behind the stove.

tHE ORIGINAL MODULE DIED AFTER 21 YEARS OF SERVICE

  • Customer: Jose from El Paso TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 13 people found this instruction helpful
First had to move the stove out of its "nest", take the side cover off, remove 1 screw and loosen the other , take the old module out and reverse the operation. That simple.
Part was supplied 1 day before promised date, awesome. Part fitted exactly as the OEM part, works like a charm, everyone happy.

the old top was cracked and rusted

  • Customer: Richard from Brooklyn NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 5 people found this instruction helpful
The new part arrived quickly and well-packaged. Removing the old top was easy enough, but needed to remove the legs (that hold it in an open position for cleaning) from the old top. The sheet metal screws holding one of them in place were rusted in place. Had to loosen with WD-40 and vice grips, but got them off without breaking or stripping the threads. They installed perfectly on the new top and the top slipped into place easily.

Grates were old and rusted and scratching the bottom of my pots

  • Customer: Sue Z from Los Angeles CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 5 people found this instruction helpful
I threw the old ones out and replaced them with the new ones. It was a no-brainer :) The parts arrived super fast. Great, no hassle service.

needed a new top-mine was so chipped.

  • Customer: Janice from Geneva OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 4 of 6 people found this instruction helpful
I propped up the old one, the way you do to clean under the top, and removed the screw on either side of the prop up post. I slid off the top and then removed the vent so I could clean it and put it on the new top. I replaced the vent into the new one, put the props back in and then the screws. It may have gone faster for someone else-I am a woman of 68 years of age and struggled a little with it. All in all, it went very well.

Replace main top

  • Customer: SUNANDITA from PARLIN NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I Realy enjoy do it myself.

Gas burner went bad

  • Customer: Kenneth from Hickman NE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I had the old burner already out, so all I had to do was insert tab into slot and then fasten with screw. Tried the burner and it worked, I just had to adjust the amount of air it received. Very satisfied with product and quick delivery.

Gas will not start

  • Customer: Paresh from La Palma CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged the range. Opened the range by removing the burners. Removed exiting spark module then installed new one. Just make sure the four plugs are correct.

oven would not ignite

  • Customer: Diane from Southbridge MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
the gas control valve was removed ,then the igniter. The new part was plugged in and the valve was applied. It started right away. I want to thank the sales man, he sold us just what we wanted, not the one we thought we needed which was 240.00. My repairs cost $42. and a meal for my son and a friend. Would reuse this service again if needed.
All Instructions for the 32-1012-00-03
1-9 of 9