Models
>
31AE5D8E099
31AE5D8E099 MTD Snow Blower - Overview
Models starting with 31AE5D8E099
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Slide Shoe
PartSelect #: PS9135084
Manufacturer #: 784-5580-0637
This Slide Shoe is rated as "Easy" to install and requires a wrench set. It is a manufacturer-approved part that comes in black and is constructed of metal. The part is used to help the snowblower sli...
$23.05
In Stock
Plastic Bushing .380 ID
PartSelect #: PS9167515
Manufacturer #: 941-0475
This is an authentic OEM part for Craftsman lawn and garden equipment. This bushing has an internal diameter of 0.380", is made of durable black plastic, is not part of an assembly or kit, and is sold...
$4.99
In Stock
Hex Flange Bearing
PartSelect #: PS9178250
Manufacturer #: 941-0245
Used mainly in snow blowers, this flange bearing is typically installed on the axle and creates a tight fit with little friction while still allowing for movement.?Your equipment will likely feature m...
$9.91
In Stock
Worm Gear 20 T, 22"
PartSelect #: PS9165943
Manufacturer #: 917-04861
This is a worm gear that is designed for use within a variety of snowblowers and snowblower tractor attachments. The worm gear is used to rotate the auger through the drive mechanism, also known as th...
$41.34
In Stock
Fuel Line Clamp
PartSelect #: PS8938782
Manufacturer #: 26460
The Fuel Line Clamp is a metal, individually sold part which clamps onto the fuel line, securing it to a port and preventing leaks. Installation is rated as "Easy" by customers and will require pliers...
$4.99
In Stock
Star Knob 5/16-18
PartSelect #: PS9109078
Manufacturer #: 720-04072A
This Star Knob, which may also be simply referred to as a Knob, is sourced directly from the manufacturer for use in lawn mowers and snow blowers. This part provides a quick-release for handles to fol...
$6.64
In Stock
Spring-Extension
PartSelect #: PS9310931
Manufacturer #: 932-0264
This is a genuine OEM sourced part that is not part of a kit or assembly and is sold individually. This Spring Extension, or Extension Spring, serves a variety of purposes, depending on your model. It...
$4.99
In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Mixer began to make a noise on speed two and higher
We took our 30 plus year mixer apart. I removed the old grease. There was some crumbly looking grease in the main housing gear section where the nylon gear is located. It looked like it had flour mixed in it. Not certain. Removed as best possible all old grease and applied 6 oz. of new Benalene grease to all of the gears. Now it do
... Read more
es not make the slight howl sound.
Read less
Parts Used:
-
LISA M from BATESVILLE, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad Camshaft made of plastic
Original engine had camshaft made of plastic. Engine had a seal leak on shaft lost oil . Result was seized bearing and stripped camshaft. Ordered a replacement camshaft and gasket. Gasket came in a week after original due date and camshaft is NOT AVAILABLE. Didn't know that at original order. Followed up twice with operator, not ema
... Read more
il and got a non-answer answer. No idea when part will be available and requested a second contact and update. Same no idea reply. Result is a waste of my time with this company, will NOT use them again.
Read less
Parts Used:
-
Dan from MILLSTONE TWP, NJ
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original shave plate badly worn
With WD-40 or equivalent, spray the four nuts on the underside of the snow blower housing that hold the shave plate to the housing. Also spray the two bolts that hold the shave plate to the side of the housing. Let sit for a few minutes and using a 1/2" box end wrench remove the four nuts on the bottom of the housing. If necessary, app
... Read more
ly heat with a torch to loosen. Using a 9/16" box end wrench, remove the nuts on the sides (these also hold the adjustable skid feet). It is recommended that the bottom bolts and nuts be replaced with 5/16-18 X 3/4" long zinc plated carriage bolts using zinc plated washers and ny-lock nuts. It is also recommended that all of th screw threads be coated with an anti- seize lubricant so disassembly at a later date will be easy.
Read less
Parts Used:
-
John from HARRISVILLE, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench set
4 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!