31315VAV Magic Chef Range - Instructions

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done

Remove old igniter ,,again had to remove rear panel of unit to get to connecter..reverse procedure to install igniter. Video very helpful.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

Removed stove from slot in wall. Bent rear left leg would not unscrew due to bent metal bracket. Used hacksaw to cut out leg, then straightened metal bracket with small hammer and was able to screw new leg in and adjust height by using level on stove before reinserting stove its slot. Recheck level after pushing back in place and adjust front legs if necessary. If not for bent metal receiving bracket, would have taken much less time. Still easy tho. R'cvd part in two days. Very quick.

I am so gald I found Parts select. I was going to order a Gas valve for $140. All the comments said the problem was a bad igniter. even though the igniter was glowing bright it was not drawing enough pawer to open the gas valve. I purchased the igniter installed it in 15 minutes and my oven works like new.

Followed the excellent instructions on your web site. I removed the oven burner assembly to make it easier to install the new igniter. The connector on the new igniter matched the one in my oven exactly. It helps to have the oven light on!

There was a lot of trepidation about starting this project. What if this is the wrong part? What if I hook it up wrong? What if the gas line is not properly secured when I'm done? This is why it took my 6 months to start this project. I hesitantly looked up my product number online and partselect.com returned three of the top ten results so I clicked it. One of the best moves I've made. When the product was shipped, I received an email with a video attached that explained how to install the igniter. This is what set partselect.com apart from everyone else and differentiated my experience from a "maybe i'll look around more next time" to "I will use partselect for all of my appliance part needs from now on" experience. Thank you for the quality customer care.

Remove oven door and bottom panel. Remove metal shield above the burner. Unscrew old igniter from brace. All this was straightforward. Then I found the old (long) igniter did not have a convenient plug that I could pull through the hole in the back of the oven. So I had to clip the two wires to remove the old igniter and stripped the insulation of these wires. Then I clipped the two wires of the new igniter since, unfortunately, I could not use the convenient plastic connector. I stripped the wires of the new igniter and connected both to the previously stripped wires coming through the hole from the back of the oven. I twisted on the ceramic wire nuts provided. It took 10-15 minutes or so to be confident these wire nuts wouldn't just fall off on their own. Then I stuffed the wire nut connections back through the hole, stuffed in all the insulation provided (necessary for the new (short) igniter!) and screwed the new igniter to the old brace. (I didn't need the new brace supplied or two long wires supplied.) Total time was about 70 minutes. The oven works well! This experience is much better than finding a repairman, scheduling the visit, etc.

Unplug power, put strap wrench around burner cap and turn counter clockwise 1/4 turn, remove 2 wires, installed in reverse.took less than 5 minutes.

Ordered the part, removed the wires (by light pulling) from the old burner and inserted them in the new one. Tried it, and it worked. Total work time, about 5 min. Amount saved, $150.

look up part, read the diognosis, order part, watch repair vidioe, order part, install mystelf. success!