Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 31213WAA

31213WAA Magic Chef Range - Overview

Get Parts and Repair Help for 31213WAA

If you know the range repair part you need, you can browse the list of all parts on the 31213WAA, or you can search by name or part description. You can also find your part by where it is located on the 31213WAA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for 31213WAA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$2.91

Light Bulb - 40W

Sold individually.

$31.07

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

$16.57

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$100.06

Spark Module

This part sends enough current to the igniter to create a spark to the bottom of the burner cap.

$5.61

Door Handle Spacer Kit

This door handle spacer assembly contains two screws and two spacers.

$22.14

SWTCH-LITE

$81.46

Burner Valve Kit

$5.63

SCREW

$4.89

Wing Nut

Glass Door Foil Tape

This piece of foil tape is twenty-nine and a half inches long. It is three inches wide and adheres to the inside top of a range's glass door.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 251 of 278 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that ... read more

gas burner ignitor failure

  • Customer: roy from East Providence, RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 102 of 115 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more

Oven would'nt light

  • Customer: Charles from Charlestown, RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 95 of 105 people found this instruction helpful
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The ne... read more