Models > 31203WAA

31203WAA Magic Chef Range - Overview

Get Parts and Repair Help for 31203WAA

If you know the range repair part you need, you can browse the list of all parts on the 31203WAA, or you can search by name or part description. You can also find your part by where it is located on the 31203WAA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your range. We’ve also included any installation videos we have for 31203WAA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$16.78

Top Burner Igniter

This top burner igniter comes with a mounting bracket.

$52.17

Flat Style Oven Igniter Kit

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

$22.97

Burner Head Cap with Spark Electrode

This part has been redesigned and no longer requires a gasket seal.

$2.70

Screw

This screw is sold individually.

$3.96

Levelling Leg

This leg is sold individually.

$51.29

Oven Rack

Used in the lower oven. Sold individually.

$31.09

Door Seal

This oven door seal prevents heat from escaping the oven cavity when in use. It contains all of the attaching clips needed for installation.

$2.70

Screw

This screw is sold individually.

$4.11

SCREW

$2.70

Screw

This screw is sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven would not work but the Broiler did

  • Customer: James from Ferndale MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 130 of 137 people found this instruction helpful
The oven had been working intermittently for a while and after repeated threats of starvation from my spouse I finally took a look even though it was summer and the grill was working fine. The Igniter would glow red when the oven was turned on but the gas would not flow to it no matter what the temperature setting. I searched online and found this site that ... read more

Oven would'nt light

  • Customer: Charles from Charlestown RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 63 of 69 people found this instruction helpful
In most cases if your oven won't light or takes a long time to light you may have a bad igniter even if it glows. To check the igniter use a voltmeter to check for 120 A/C volts going to the igniter and3.5 A/C volts going between the ingniter and the gas valve. My bad ingniter glowed but had only only 3.0 A/C volts going to the gas valve for the oven. The ne... read more

gas burner ignitor failure

  • Customer: roy from East Providence RI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 52 of 59 people found this instruction helpful
Lift out sealed burner assembly rear of stove first while careully sliding to rear to disengage ignitor probes.Remove philips head screws from bottom sheet metal housing to expose bottom of burners Remove gas tube assembly screws and move tube away carefully.Unplug wires from ignitor.Remove screws for ignitor .Remove ignitor, I noticed that rust and dirt ha... read more