3110PRA Magic Chef Range - Instructions

removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.

I think the installation instructions are fairly self explanatory. This is the second item I've ordered from Parts Select and I'm thrilled with their service. The items are always less expensive than other sites and they deliver what they promise. I would highly recommend them.

Popped in there real quick. Wish I would have done it sooner, my oven heats up much faster.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done

Remove old igniter ,,again had to remove rear panel of unit to get to connecter..reverse procedure to install igniter. Video very helpful.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

took oven door off easy just lift up took bottom tray to oven out took bottom draw of stove out removed tin panel cover 2 screws to unplug igniter took 2 screws out of igniter and pulled unpluged wire through insulation. installed new igniter 2 new screws put wire through insulation and pluged it in. The only thing to check is matching the plug ends correctly before pushing them together.

I tried to get black drip pans to replace the ones I had which were well in need of changing. They no longer make the black so I found the silver ones on your site and thought for the price I would try them. They are wonderful and very reasonably priced. I ended up buying a spare set for later. Thank you for such great products and prices.

Basic instructions provided were accurate. Most difficult part was bending down and reaching across the oven door. A general information note would have been helpful. The circuit that feeds the igniter and the gas valve is a series circuit. So, even though the igniter was glowing cherry red, the igniter was still the cause of the gas not flowing, The voltage drop across the igniter was larger then normal causing the voltage to the gas valve to go down and to be insufficient to allow the gas to flow.

After watching your do-it yerself video, I turned off the gas and unpluged ac power cord, I removed the stove door and then removed the bottom tray inside the stove unscrewed tray plate pulled buner out of its housing. I then unscrewed the two screws to the old ignitor and unpluged it. Pluged in the new one screwed it to the burner bracket, put everything back togher then tuned on the stove. IT WORKS!!

Removed the oven burner changed the igniter reinstalled the burner still didn't operate,gave up purchased a new range. I liked dealing with your sales department very friendly.

This is one of the easiest home repairs I have ever done. I shut off the gas and unplugged the oven. I removed the door and shelves. I then removed the two screws that secured the igniter and pulled the connector through the hole in the back of the the oven. No need to splice any wires as the replacement igniter came with the correct connector. It was then just a matter of reversing the process. Very simple and quick fix.

Replaced the oven igniter and oven works perfectly 30 seconds to light